NHTSA Owner Complaint Log
This page lists owner-reported complaints filed with NHTSA for the 2016 Ford Explorer. Complaints are unverified consumer reports submitted to NHTSA and do not by themselves prove a defect or defect rate.
Data synced from NHTSA on May 4, 2026
The explorer started having issues with the heater not working when stopped. After some research it recommended that we check the coolant level. The coolant was low. Then we refilled it and then it happened again 3 weeks later and the coolant was low. This made us believe there was a coolant leak. After removing the bottom cover under the car it was saturated with coolant with drops coming from various areas on the passenger side. We took it to a mechanic and then transferred to a dealer and both confirmed it was the water pump. Ford negligently designed the water pump within the engine with the timing chain. If enough of the coolant mixes with oil it will cause the engine to seize and the car to shut off. I have two little kids that are in the car with me. This negligent placement can lead to cars seizing in unsafe areas. It was confirmed by a private mechanic and a ford dealer and there were no warning lights. Other than the heat not functioning properly there we no other signs or lights of water pump failure.
My steering wheel completely locked up and we couldn't turn it or anything. After repetitively trying to move it the steering wheel finally came loose. I was able to take it to a mechanic and he said its the steering rack but since it completely locked up and was unable to move the steering wheel I needed to contact you. Ford does have a recall for the steering rack but it does not include my year of Explorer.
The contact owns a 2016 Ford Explorer. The contact stated while driving approximately 60 MPH, there was an abnormal tapping sound coming from the vehicle and observed that the center trim piece on the passenger’s side door frame was blown off the vehicle. The contact stated that the driver's side door trim was coming loose. The contact used tape to hold the trim piece in place. The contact had called a local dealer and was informed that the trim on the door frame was not included in NHTSA Campaign Number: 24V031000 (Structure). The vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 51,000.
The contact owns a 2016 Ford Explorer. The contact stated that while driving at an undisclosed speed, the front driver's side air bag warning light illuminated. The contact stated that the failure occurred intermittently, however, the failure had occurred three times. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 55,000.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 25V347000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact used tape to secure A-pillar trim to prevent the trim from detaching from the vehicle. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.
Subject: Urgent Vehicle Safety Complaint Regarding Defective Water Pump in Ford and Lincoln Vehicles I am writing to bring to your attention a critical safety concern affecting numerous Ford and Lincoln vehicles worldwide, specifically those equipped with Cyclone (Duratec) engines. The issue at hand revolves around a defective water pump, which has manifested in various models, including but not limited to: - Ford Edge - Ford Explorer - Ford Flex - Ford Fusion - Ford Taurus - Lincoln Continental - Lincoln MKT - Lincoln MKX Owners of these vehicles are experiencing a significant and alarming risk of stalling in traffic, posing a severe threat to both driver and passenger safety. The potential consequences, including the increased likelihood of accidents and fatalities, demand immediate attention and action from Ford Motor Company who has been sued multiple times and is avoiding to respond to the judgements against them trying to use any excuse not to pay. It is imperative to address this widespread concern promptly, as the safety and well-being of Ford and Lincoln vehicle owners are at stake. I urge your organization to conduct a thorough investigation into the defective water pump issue, implement a comprehensive recall, and provide a reliable solution to rectify the problem. Your commitment to prioritizing the safety of consumers is paramount, and I trust that Ford Motor Company will take swift and decisive action to remedy this situation. By addressing this issue promptly, you not only ensure the protection of current owners but also uphold the reputation of Ford and Lincoln in the automotive industry. It's impossible to say that it is a mere coincidence that thousands of Ford vehicles have the same defect with exactly the same engine and symptoms. Thank you for your immediate attention to this matter, and I anticipate a proactive response that prioritizes the safety and satisfaction of Ford and Lincoln vehicle owners.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was taken to the dealer who removed the trim to determine if the trims were defective; however, the vehicle was not repaired. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while the vehicle was parked, she became aware that the A-pillar trim was missing. The contact stated that a couple months later the rubber gasket on the driver’s side had flown off. The dealer was made aware of the failure but confirmed that parts were not yet available and advised the contact to call the NHTSA Hotline. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 101,000. VIN tool confirms parts not available.
Trim piece on passenger side broke in half while driving and hit another car. No damage reported but it almost caused accident. Confirmed this is the recalled piece.
The contact owns a 2016 Ford Explorer. The contact stated that when the vehicle was shifted into drive(D), the vehicle started shaking abnormally. The vehicle was taken to an independent mechanic where it was diagnosed with a failed transmission and that the transmission needed to be replaced. The contact was informed about TSB: [XXX]. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to report the failure to the NHTSA Hotline. The failure mileage was approximately 110,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2016 Ford Explorer. The contact stated while driving 40 MPH, the vehicle lost power steering functionality. The service stability track, traction control, and the loss of power steering warning lights were illuminated. The contact stated that he used physical strength to steer the vehicle after the power steering assist failure to the residence. The vehicle was taken to a local mechanic who diagnosed that the angle sensor was defective and there was a loss of communication. The contact was informed that due to the failure and the loss of communication, the power steering assist, hill assist, and traction control features were disabled. The vehicle was not repaired due to a needed part being on backorder since November 2023. The manufacturer was notified of the failure and a complaint was filed. The failure mileage was approximately 69,000.
went to drive my vehicle and when i turned exiting my driveway , my steering was stiff, hard to turn. shutting off vehicle and restarting sometimes helps, but now it is always no power assist. No warning lights, messages or check engine lights at all. just lost power assist. I figure it is another rack n pinion steering assy by all i read online. This should deffinately be a recall. 2011-2013 had the same issue and was issued a recall. Why is this not? it is so dangerous. Get on the ball and do something. 2016 explorer xlt
The water pump failed causing coolant to leak into the oil pan causing my vehicle to die suddenly and without any warning lights or messages on a high speed, heavy traffic metropolitan interstate/highway (35W in Minneapolis). I was commuting home from work. It was completely dark. I was in the far left lane and had to quickly maneuver across 4 lanes to the right shoulder narrowly missing being slammed into by other cars before the vehicle completely died. I waited for a towing service in the dark while other vehicles including semis sped extremely close to my vehicle with only my hazards to warn them I was there. Vehicle was towed to a local repair shop and they confirmed the water pump failed and coolant leaked into the oil, ruining the engine. I've been researching online and am reading that this is a very common and known issue with lawsuits. My vehicle only had 132k miles. This issue put me in a dangerous, potentially life-threatening situation that could have caused harm to me and the many other drivers and their passengers on the highway - and it needs to be addressed and dealt with - for me and apparently the many others that have been affected by this manufacturers defect.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The rack and pinion steering has gone bad. This is causing the vehicle to be hard to drive as it is very difficult to turn the wheel and control the vehicle. This is making it dangerous to drive as you are unable to turn the wheel very well.
The contact owns a 2016 Ford Explorer. The contact stated while driving at various speeds, the vehicle failed to properly accelerate. The contact stated that the failure was intermittent and mostly occurred while driving up an incline. The cause of the failure was not yet determined. The manufacturer was notified of the failure, but no assistance was offered. The local dealer was not yet contacted. The failure mileage was 137,000.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact stated while driving 5 MPH and coming to a complete stop, the vehicle shuddered. The contact stated that the vehicle shuddered increasingly while at a complete stop. The contact stated that upon depressing the accelerator pedal to drive, the vehicle failed to respond. The contact stated that she depressed the accelerator pedal harder, and the vehicle responded. The check engine warning light was illuminated. Additionally, the contact stated that the failure recurred while reversing. The contact stated that the failure had been recurring. The vehicle was taken to the dealer, where it was diagnosed and determined that the torque converter, the Body Control Module (BCM), the solenoid body and transmission fluid and other unknown parts needed to be replaced. The vehicle was not repaired. The contact related the failure to Ford Campaign Numbers: 20B27 and 20N07. The manufacturer was notified of the failure and a case was opened. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 126,000.
The contact owns a 2016 Ford Explorer. The contact stated while driving 20 MPH in the snow, the vehicle started fishtailing. The contact was able to continue driving at slow speeds. The vehicle was taken to an independent mechanic for an alignment; however, the mechanic informed the contact that the rear suspension toe links had failed and needed to be replaced. The mechanic determined that the failure was related to NHTSA Campaign Number: 21V537000 (Suspension) and referred the contact to the dealer for assistance. The contact stated that the failure recurred while driving in the rain. The contact veered to the side of the road. The contact was able to continue driving after the rain stopped. The contact stated that the failure had been recurring increasingly while driving over potholes. The vehicle was taken to the dealer, where the contact was informed that the vehicle was not covered under the recall because the VIN was not included. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was unknown.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
There was no incident however I received a recall for a windshield piece that was back in 2024 and supposedly would be available for repair in the latter half of 2024. However nothing has been sent to me regarding this and when the piece came off it cracked my windshield so I have a crack across that as well.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the driver’s side A-pillar trim had started to detach from the vehicle. The approximate failure mileage was 100,000. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE). The local dealer was contacted and informed the contact that parts were not yet available for the recall repair. The vehicle was not repaired. The manufacturer was contacted regarding parts not being available. The contact had not experienced a failure.
On 1/28/24 We were traveling 50-60 mph when all of a sudden we heard a popping noise and noticed the trim on drivers side was loosening. We were able to slow down and pull over which was when the trim then blew off. My husband retrieved the trim (which we now know is referenced as the a-pillar) off the side of the road. obviously this could have been worse if it had struck another vehicle /caused someone to swerve. I then contacted the ford dealership as we learned this was part of a recall. They came out and ended up fixing the roof rack of which that was not my complaint. Clearly there was a miscommunication on what my problem was when called in. I then took it into dealership for them to observe. He printed out a quote to fix pillar at 400-500$ but could not guarantee reimbursement by Ford. I called Ford motor company who gave me a case number and corresponded with local dealership. Essentially I have been told bc this is an advanced notice recall there is nothing that can be done to fix current situation. I will now be driving my vehicle without the trim and also concerned how long til the passenger side blows off as there was no loosening or sign of defect prior to this event. How will weather affect the exposed trim and windshield/aerodynamics. I just hope Ford will expedite the process of repair for safety first but also the look of the vehicle as this is a reflection of their company . My case number is CA547669778 approx mileage 123,000
The contact owns a 2016 Ford Explorer. The contact stated while driving 75 MPH, the A-pillar trim on the driver's side detached from the vehicle and flew off the vehicle. No warning lights were illuminated. The vehicle was not diagnosed or repaired. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed that the part was not yet available. The manufacturer was not notified of the failure. The failure mileage was unknown.
2016 Ford Explorer. the air bag warning light was illuminated it was coming off and on and now stays on. took the vehicle to the dealer who confirmed that the vehicle was not under recall for the failure. The vehicle had not been repaired.
The contact owns a 2016 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 24V031000 (STRUCTURE) and 25V347000 (STRUCTURE); however, the parts to do the recall repairs were not yet available. The contact stated that while driving at an undisclosed speed, the driver's side A-pillar trim detached from the vehicle. The vehicle was not diagnosed or repaired. The contact stated that on a separate occasion, while diving at an undisclosed speed, the front passenger’s side A-pillar trim detached from the vehicle. The vehicle was not diagnosed or repaired. Most recently, the contact stated that the B-pillar trim detached from the driver's side and passenger's side. In addition, the trim around the front windshield also detached. The vehicle was not diagnosed or repaired for the most recent failure. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that while driving at various speeds, the driver's side and passenger's side windshield exterior A-pillar trims became loose. The local dealer was contacted. The vehicle was not repaired. The contact used Scotch tape to hold the trims in place. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 50,000.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated while driving approximately 30 - 40 MPH, the windshield side A-trim panel detached from the vehicle. The contact stated that the following day the passenger’s side trim and two clips had detached causing the failure. The trim on the bottom of the front and rear doors between the front and rear wheels had become loosened as well. The contact stated that there was a film on the headlights causing the headlights to not illuminate properly. The contact used WD-40 on the headlamps to remove the film for proper illumination. The vehicle was taken to the dealer who inspected the vehicle and removed the trim cover, as instructed by the manufacturer, to determine if the windshield mounting plate, was an older version. Based on the inspection, the dealer determined that the vehicle had failed and there was no need for the part mentioned in the remedy to be used for a repair. While completing the inspection the trim cover had to be removed and the trim cover became loosened, causing further damage with other trim panels detaching from the vehicle. The contact informed the dealer, and the dealer offered to secure the trim with tape. The dealer also advised the contact to use duct tape to further secure the area. The contact stated that the following day the tape had raised up. The contact called BP Ford of Long Beach (2950 N Bellflower Blvd, Long Beach, CA 90815) and was informed that the part could be ordered to complete the recall repair. The dealer informed the contact that the trim could be replaced; however, the recall remedy part was not yet available. The headlight and lower trim on the body of the vehicle had not been replaced. The manufacturer was made aware of the failure. The failure mileage was 83,000. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 24V031000 (Structure) and 25V347000 (Structure). The contact stated that water was leaking onto the passenger’s side floorboard and passenger’s side door, causing an electrical short with the windows. The contact stated that the window was stuck. The contact left the windows opened to air out the vehicle. The contact used duct tape to secure the structure. There were no warning lights illuminated. The local dealer was contacted and confirmed that parts were not yet available. The contact was added to a waiting list. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 86,800.
We were driving down [XXX] between Houston and San Antonio on [XXX], when we heard a loud noise but felt nothing. When we were ready to leave our destination, the front-driver's side windshield panel was gone. It had blown off going down the road. There was no warning that the panel was loose nor any warning that it was gone. We could have been seriously hurt or killed if the part had come through the windshield. We are thankful that it did not hit and or kill a motorcyclist or cause a wreck where someone else could have been hurt or killed. There is no way to know if a later travelling car received damage due to the part being in the freeway or if it caused a wreck. I am also concerned that the windshield will leak since there is nothing covering the edge of the windshield. My car is available for inspection, but I do not have the panel. I spoke with Mia at Ford Customer Service (800-392-3673) on January 22, 2024. There is nothing that Ford is doing at the time to help car owners. Mia said to keep all paper work incase Ford decides to do some repairs in the future. I will get my car fixed but not at Ford. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2016 Ford Explorer. The contact stated that while driving at an undisclosed MPH, the roof rack rails detached from the vehicle. No warning lights illuminated. The vehicle was taken to the dealer and it was confirmed the entire roof rack rails had detached from the vehicle. The vehicle was previously repaired under the Customer Satisfaction Program recall 21S22. The contact stated the failure persisted. The vehicle was not repaired due to cost. The contact stated the dealer informed him he must pay for the repairs because the vehicle had been previously repaired under the recall program. The manufacturer was made aware of the failure and referred the contact back to the dealer. The failure mileage was approximately 160,000.
I REPORTED A PROBLEM 1/23/24 CONCERNING THE TRIM BLOWING OFF BY THE FRONT WINDSHIELD, I SAW ON THE NEWS THAT THIS IS A RECALL ISSUE BUT I ALSO THINK THAT THE COWLING WHERE THE WIPERS ARE ATTACHED SHOULD BE LOOKED INTO, THIS PIECE IS FALLING APART AND WHEN DRIVING THE WIND GETS UNDER THE TRIM PIECES CAUSING IT TO BLOW OFF.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the front driver’s and passenger’s side window trims had detached from the vehicle. The vehicle was taken to a local body shop where the trims were replaced. The dealer was contacted. The manufacturer was made aware of the issue. The failure mileage was 70,000. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that while driving approximately 65 - 70 MPH, the vehicle emitted a loud bang that came from the passenger’s side of the front windshield. Once the contact was able to park the vehicle, the vehicle was inspected, and the contact became aware that the trim on the passenger’s side of the front windshield had detached. The same failure occurred on the driver’s side of the windshield about a week later while driving at approximately 55 MPH. The dealer was contacted. The manufacturer was not made aware of the issue. The failure mileage was unknown. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the keypad to unlock the driver-side front door with the passcode detached from the vehicle. The dealer was contacted. The manufacturer was not made aware of the issue. The failure mileage was 58,630. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed that the parts are not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The manufacturer opened a case and referred the contact to the NHTSA Hotline for assistance. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2016 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.