2020 Ford Explorer Complaint Log

The contact owns a 2020 Ford Explorer. The contact stated while driving at various speeds and attempting to accelerate, the vehicle was jerking abnormally. There was no warning light illuminated. The vehicle was taken to the dealer where it was diagnosed and determined that the main control valve had failed and needed to be repaired. The vehicle was repaired but the failure persisted. The vehicle was returned to the same dealer where it was diagnosed that the CDF clutch bushing had seized. The vehicle was not repaired. The manufacturer was made aware of the failure and opened a case. The manufacturer had referred the contact to the NHTSA Hotline to file a safety complaint. The failure mileage was 25,000.

When shifting from park to reverse, with foot completely on brake, the car will roll backwards several feet before stopping. Happens multiple times a month. Very dangerous as it rolls back into oncoming vehicles in parking lots. It is difficult to replicate as it is an intermittent problem. There is no prompting by the vehicle that there is an issue before hand. The only notable difference is the brakes are very firm while the vehicle is rolling and cannot be pressed in further.

The contact owns a 2020 Ford Explorer. The contact stated that on various occasions after starting the vehicle, the brake system warning light illuminated. The contact stated that the warning light disappeared after driving; however, the failure persisted whenever starting the vehicle. The vehicle was taken to a local dealer, where the failure could not be duplicated. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 20,000.

The contact owns a 2020 Ford Explorer. The contact stated while at a stop light, the vehicle accelerated and jerked with a delay while shifting gear. The check engine warning light was illuminated. The vehicle was taken to the dealer, but no cause for the failure was found. The failure persisted. The vehicle was not diagnosed or repaired. The dealer was contacted and stated that the vehicle was not under recall. The manufacturer was not contacted. The failure mileage was 72,000.

While driving the the vehicle's RPM increases violently, but no speed is increased or kept. Also, the car will jerk while driviing (at any speed). These are both separate cases. The occurs while driving on interstate, driving onto a ramp and entering traffic, while entering intersection and pulling into traffic, leaving a stop light and trying to drive through an intersection. It is being looked at by a dealer. Dealer says they cannot replicate. No warnings. I have been at risk many times trying to accelerate and not being able to when car slows or comes to a almost complete stop as entering traffic.

The transmission has failed. Started with hard shifting between gears, was to the dealership. Worked on it for 2 days, could not fix, gave back now as I was going thru an intersection went into a "neutral" type mode, lost all power coasted then picked up and started going again. Almost got rear-ended because of this. No messages appeared.

I hit my brakes at a traffic light and the dash board lite up. With the following messages. Service Advance trac, 4WD Fault service required, see manual, hill start asst not available, auto hold fault, tooknto dealer tried to charge $600 for a diagnostic, codes were ran all codes are communication codes. Have no abs brakes. Took to another shop they couldn't figure it out. Called Ford. They refer back to dealer who what's to charge more money for diagnostics and the 33 codes they say are in the computer. Big safety issues. Happened just after 60,000 miles before looking at it dealer stated it wouldn't be covered under powertrain warranty anyway. Can't upload photos from phone for some reason.

The issue was initiated when you turn the vehicle on. The vehicle would process through normal startup modes, and then produce several error codes and light illuminations, all within several seconds. The illuminations would consist of; Traction Control Error, Auto Hold Error, Descent Control Error, Lane Assistance Error, and Collusion Avoidance Error. This would then maintain the error during the trip or until the vehicle was powered off for several minutes. After the power cycle, the vehicle would start and show no symptoms of any error codes, at all. This would happen in several different instances a day, lasting several months. In several of my cases, this would disable traction control for longer periods of time throughout the day or week as well. This places extreme risk to drivers who may not know that there are so little standard safety features active while behind the wheel. Additionally, it affects drivers ability to stop, which traction control and auto hold disabled, and reduces the safety of everyone else on the road. I took the vehicle twice to a Ford Certified dealer and repair shop to investigate the issue. The technician was able to verify the codes that arose from the incidents. However, the first instance when I took the vehicle in, they were unable to locate a solution to the problem. After the second visit, they recommended a complete reprogram of 5 major computer modules that have created the system error. I inquired since this seems to be an issue widespread that they could not identify as a user error, but rather an equipment defect. They indeed charged me for the service when this should be something that should be issued a recall and fixed at a wide spread level. The safety of others while on the road are effected and may lead to serious vehicle accidents as a result of the failure of the vehicle component.

While vehicle was in park it continued to go in reverse with warning lights showing "PARK NOT ENGAGED".

The Ford Explorer ST when shifting into reverse, sporadically, the backup camera presents a blue screen, preventing all visibility while attempting to drive in reverse. It appears that none of the warning signals are operational when getting close to people or objects when the camera isn't working, thus presenting a hazardous condition as all safety features do not function. Apparently, there are similar recalls on some Explorer models but my particular vehicle is one that is not included in the previous pool of vehicles that are eligible for the recall repair.

When I release the parking brake and put the car in reverse, the car starts to roll while my foot is still actively pressing the brake. Brake pedal feels locked. It’s happened a handful of times but is not consistent and hard to replicate. This, of course, puts anyone in my car in danger and anyone around my car. I’ve taken it to the dealership and elevated it to corporate, but they say they can’t do anything since they can’t replicate it on site. Based on website forums, this is a common issue. When it happens, there are no warning lights or anything indicators. Again, to summarize, car rolls when brake is pressed intermittently.

The contact owns a 2020 Ford Explorer. The contact stated that while activating the windshield wipers, the driver’s side windshield wiper was inoperable. The vehicle was taken to the dealer and the driver’s side windshield wiper was replaced; however, the failure reoccurred. The vehicle was taken to the dealer and the mechanic stated that the bracket had sunk into the vehicle causing the wiper to not function correctly. The mechanic stated that an additional screw would be added for the wiper to function as needed. The vehicle was not yet repaired. The manufacturer was not contacted. The failure mileage was 48,000.

The issue started after the car was brought in for a recall. They said it was only a software update, so it may be a coincidence. When starting to drive the car after being in park, the front of the car sounds like things are screeching and halts the car suddenly without any warning. When in reverse a note comes on that rear assist is unavailable as it stalls. When in drive no notice comes on but the car comes to a halt. It will work if you turn it off and on and try to drive again but happens in the middle of the street. This is a huge safety concern while driving on the road to be hit by someone, injured by the whip lash from the stop. We have very young kids and refuse to put them in the car in fear of this happening with them in it again, or happening in their daycare parking lot with other kids around. We took the car twice to the dealership by our house, however they were unable to duplicate the issue and says there is nothing they can do.

The contact owns a 2020 Ford Explorer. The contact stated while reversing there was an abnormal bumping sound coming from the front of the vehicle. The contact stated that the vehicle then failed to drive forward after the failure. The tow truck was called to the scene; however, while lifting the vehicle onto the tow truck it was discovered that the front passenger’s side control arm had fractured. The vehicle was towed to the local dealer. No further information was available. The vehicle was not yet repaired. The manufacturer was notified of the failure. The failure mileage was 80,000.

The contact owns a 2020 Ford Explorer. The contact stated that while exiting the vehicle, she observed the front driver's side seat control housing separating, hindering the use of the seat controls. The failure was later observed in the front passenger’s side seat. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 16,000.

The contact owns a 2020 Ford Explorer. The contact stated that while driving approximately 40 mph, the vehicle failed to move and was seized. There were no warning lights illuminated. The vehicle was taken to the local dealer where it was diagnosed the transfer case, gear, transmission, and engine needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The approximate failure mileage was 68,000.

The contact owned a 2020 Ford Explorer. The contact stated while driving 15 mph, the vehicle began to decelerate its speed on its own. The contact stated no warning light was illuminated. The contact was able to park on the side of the road and saw fire located on the front passenger side wheel. The contact, his wife, and grandson were able to safely exit the vehicle before the vehicle was engulfed by the fire. The contact stated no one was injured nor sought medical attention. The fire department extinguished the fire and filed a fire report. A police report was filed. The insurance company deemed the vehicle total loss. The contact towed the vehicle to towing lot. The contact drive to the local dealer and made them aware of the failure. The manufacturer had not been informed of the failure. The failure mileage was approximately 30,000.

While driving on normal suburban roads, error messages appear on the instrument display every two to three days: 4WD Fault Service Required, Pre-Collision Assist not available, Service Advance Trac. The check engine light or wrench icon appears on the instrument display, and the stability trac icon appears on the instrument display. When this happens, the adaptive cruise control does not function. Safety of the vehicle and driver are impaired by major safety system(s) do not function, such as the stability control and the collision avoidance feature. I have brought the Explorer in to one dealer one time, and another dealer two times. A repair to the half shaft speed sensor has been performed twice, however the problem still persists. This problem first appeared on the vehicle in July of 2022 at 44,000 miles.

From the carfax report But I signed when I bought this vehicle Said that the transmission was fixed, It's sleeping and making a loud clinking noise !!! The Ford Explorer has been in the shop for almost a whole year for the same issue That was said on the car factory port was supposed to be fixed Well before I bought it from this car lot.. I would like to know who's the liar carfax are this dealership !!! Do I hold you are responsible for the false Information that I was led to believe are the dealership ZECK FORD !! I'VE BEEN SOLD A LEMON and want to know to whom due I Hold responsible for selling me a unreliable undependable Piece of junk that is currently in the dealership right now and ZECK FORD It's refusing to service it Which is the dealership I purchased it from also got your car fax from!! I'm making payments on this vehicle and also paying for a rental car all out of pocket and I'm tried of playing games and also done with this LEMON I'VE BEEN SOLD!!! Look at the carfax report and see for yourself ZECK FORD has called my family and me Liars July 2022 up to now still broke down

When engaging reverse the image on the screen turns solid blue. I can turn the vehicle off and back on and sometime this resoles the issue. It has happened at least a 12 times in the last couple of weeks. I did some initial investigation online and it appears that my vehicle is experiencing the same symptoms as a recall announced by Ford. https://www.consumerreports.org/car-recalls-defects/ford-and-lincoln-recall-2020-models-for-faulty-backup-cameras/

The contact owns a 2020 Ford Explorer. The contact stated that the back over prevention camera screen was black intermittently. The contact then received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) and the vehicle was repaired; however, the failure persisted. The vehicle was returned to the dealer but was not diagnosed. The vehicle was not repaired. The manufacturer was made aware of the failure and opened a case. The manufacturer referred the contact to NHTSA Hotline to report the failure. The failure mileage was 52,700.

The contact owns a 2020 Ford Explorer. The contact received notification of NHTSA Campaign Number: 22V255000 (Power Train) and the fix stated that the dealer would update the electronic parking brake software but not replace the bolts. The contact was concerned that an update would not fix the issue as the failure was with the bolts. The contact had not experienced a failure. The contact stated that he called the dealer and it was confirmed that the remedy was to update the electronic parking brake software. The manufacturer was contacted and confirmed the remedy and a case was opened. The manufacturer offered no further assistance. Parts distribution disconnect.

The contact owns a 2020 Ford Explorer. The contact stated that while having a routine oil change completed at the local dealer, she was informed about a recall update. The contact stated that while driving, the electronic parking brake engaged. The contact stated that the failure had occurred while the vehicle was in park(P) and also while driving. While shifting into drive or reverse, the vehicle was jerking. The Auto START/STOP was disengaged. Additionally, the brakes were continuously grabbing while attempting to stop the vehicle. There were no warning lights illuminated. The vehicle was taken back to the local dealer but the vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA. The approximate failure mileage was 19,624.

While driving on a busy , high speed road the pre collision error message came on the screen. It felt like the truck started applying brakes causing us to jerk. Although I tried I could not accelerate. Several error messages were sent to the ford app about the Powertrain. This put my kids and my safety in jeopardy. Our speed was greatly reduced and someone easily could have hit us. This is the second time I’m taking this truck in for service with the same problem. I have less than 25 k miles on this truck. This should not be happening.

While driving on the highway the 2020 Ford Explorer XLT briefly lost all power, exhibited jerking through the drivetrain and erratic engine RPMs, before regaining power. Thereafter, the vehicle consistently jerked during acceleration and deceleration, with an audible clunking sound, as if the vehicle was transitioning gears or drive modes (2WD-AWD). Mileage noticeably dropped and transmission and engine RPM performance was erratic. Only a warning was issued with no indication of high severity, only reduced power. Upon further driving, the erratic behavior persisted included losing power in highway traffic and putting occupants at risk of accident. Vehicle has only 14,500 miles at time of issue with full dealer service history. As of this writing, it is being brought to the dealer for service.

The backup camera display on the infotainment system when the vehicle is placed into reverse the screen illuminates in a blue screen not showing the surrounding area normally viewed. This issue was confirmed by Ford technician, an update to the system was supposed to fix the issue, the following day after the update to the vehicle, the same issue arose, I took the vehicle to the dealership, the issue was reproduced, the service writer documented the issue with a photo. This creates a backing safety issue as the proximity sensors where not working while in blue screen to warn of objects or persons while in reverse There where no warnings or onboard messages indicating an issue with the beck up camera This issue still has yet to been repaired by the dealership.

The contact owns a 2020 Ford Explorer. The contact stated while reversing, the rearview camera image turned black or blue. A message indicating that the rearview camera was inoperable was displayed. The contact stated that the vehicle was taken to the dealer, where an unknown software update was performed several times; however, the failure persisted. The contact received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted and referred the contact to the manufacturer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and referred the contact to the dealer for assistance. The failure mileage was approximately 16,000. VIN tool confirms parts not available.

The contact owns a 2020 Ford Explorer. The contact stated that while in reverse, the camera screen went blank. There were no warning lights illuminated. The contact received notification of NHTSA Campaign Number: 23V342000 (Back Over Prevention). However, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 40,000. Parts distribution disconnect.

The contact owns a 2020 Ford Explorer. The contact stated while placing the gear shifter into reverse(R), the Back Over Protection screen turned blue. The side and front camera's functionality worked as intended. The vehicle was repaired under recall; however, the failure recurred several times. There were no warning lights illuminated. The vehicle was diagnosed at the local dealer with a defective camera. The camera was replaced. The manufacturer was notified of the failure. The approximate failure mileage was 50,000.

When there is heavy, consistent rain, the rear passenger side window leaks. I took the vehicle in for service under warranty and they told me Ford said the vehicles are not built to withstand heavy, consistent rain. Ummmm, what? This is not a small issue. During one downpour, there was at least an inch of water in the rear storage compartment. I live in eastern TN and we do tend to get a lot of rain, but I do not see how this window does not seal out the water.

Backup camera display shows intermittent blue screen.

Vehicle stalled on interstate on my way home from picking it up. Had been at dealer for nearly a month for heater repair. Cost me $250 to get it towed back to dealer. Very dangerous situation. I was lucky to be able to get it oof the travel lanes before someone rear ended me at high speed. Very frightening.

When reversing the rear camera display turns blue and I'm not able to see anything behind me using the safety camera feature. I rely on the camera to assist with detecting people or objects in my blind spots while reversing and intermittently the display turns blue. There was a recall for this make and model and manufacture date, but the vehicle is not included in the recall. Recall information - Rearview Camera Recall 21C09. The dealership can't reproduce the issue because it's intermittent and there are no error codes, so they won't replace the camera. They've tried several software fixes but the problem continues. No warning messages displayed when the issue occurs. Thanks.

Sometimes the rear camera view shows a blue screen while the other camera views work. I have to restart the vehicle to make it work.

The front panel of my 2020 Ford Explorer ST panoramic sunroof exploded on May 6, 2022. Fortunately, I had closed the sun shade two days prior while on vacation in Florida. It was not due to being hit by debris as traffic was light and no trucks nearby. I was driving westbound on I-4 between Orlando and Tampa when a sudden "BOOM" occurred. I looked around as to what happened as their was no vibration or shuttering in the steering. I then heard glass shattering. When I could safely pull to the side of the road to inspect, the entire front panel of the sunroof was gone except around the perimeter. If I had not previously closed the sun shade, the tempered glass would have been in my eyes and any passengers in the front or rear seats. The local Ford dealership initially stated that the sunroof would be covered by warranty while waiting (6 days) for the back-ordered sunroof to be delivered. Then after being in the Service department for 2 days, they stated it would not be covered under warranty. I called Ford Corporate to complain, but they were only concerned if there was an open recall on the sunroof and there were none. They seemed disinterested in the safety aspect of the issue. I have since paid for the repair and filed an insurance claim. I know what a rock hitting the windshield or hood sounds like... this was not a rock, but a low, "mini-sonic boom"... the sunroof literally exploded. I usually do not pull the sun shade closed, but did so while in Florida although it was not extremely hot , between 87-92 degrees at around 9:30am, clear and sunny.

My car has a transmission problem. 6 times now, it fails to re engage after I took my foot off the gas pedal. This happens when I am attempting to accelerate after slowing down in fast moving traffic when I really need to be able to accelerate. This caused a very dangerous situation due the the fact that I am trying to get into a faster moving lane of traffic. This put me and others around me at risk. The car is at the dealership now. They say that they have identified the problem. No parts are available to fix the problem. Covid, you know!!! 6 weeks for parts! There are many complaints on the internet expressing the same problem. I also read that Ford has been buying some of this year and model back due to "This" problem. What does NHTSA know? There have been "Warning Messages", But when driving at 70-75mph and there is a problem like this, I did not have time to read it before it disappeared. Scared the crap out of me as I was put into a dangerous situation.

Driver side, passenger side window switches. On the toggle switches, the chrome is the laminating and has become very sharp. Realized this was taking place after cutting finger. Delamination Continuously getting worse.

THE HANDS FREE LIFT GATE CLOSES ON ITS OWN. THIS HAS HAPPENED MORE THAN A DOZEN TIMES SINCE I BOUGHT THIS VEHICLE 3 MONTHS AGO. ANY PERSON STANDING AT THE REAR BUMPER (NOT PUTTING THEIR FOOT UNDER THE BUMPER) ACTIVATES THIS SELF CLOSING PROCESS. THE DOOR HIT ME IN THE HEAD TWICE.

I have brought my vehicle to the dealership for repair of the Safety Recall for my car. They stated that they repaired the car. However the problem still exist. I have taken images and videos of the problem.

Reverse camera blue screen is appearing again after the 1st recall “fix”. Apparently this is becoming quite common, as I am in many Ford Explorer groups. Many others have this happening after their “recall fix” as well. Some even appear to have this happening after multiple times of recall “fixes”. Ford should be held accountable for not addressing a safety concern with a concrete solution. I have asked others within the groups to also submit incident reports.

The gas pedal snapped off where connected to the floor.

The contact owns a 2020 Ford Explorer. The contact stated that while the vehicle was parked, unattended on an incline, the vehicle rolled backward without warning. The contact was able to place her hand on the brake and stop the vehicle. There were no warning indicator lights illuminated. The contact scraped her knee but no medical attention was provided. The contact stated while sitting in the driver's seat, the vehicle rolled backward. The driver was able to depress the brake pedal. The vehicle was taken to the local dealer where they could not duplicate the failure. The vehicle was not diagnosed or repaired. The manufacturer was notified but no additional assistance was provided. The failure mileage was 22,000.

The back up camera is malfunctioning on my vehicle. It presents a blue image with the back up camera and a blue image on the 360 camera. Everything that I have read shows it is a recall, but my VIN does not have a recall.

The component that has failed is on the exhaust listed as the flexible exhaust pipe assemble part N1MZ5G203A. The part has no visual damage but consistently rattles while idle. The vehicle has been well taken care of but the part appears to be defective. This appears to be the same issue as NHTSA Technical Bulletin 20-2282. There are no safety concerns at this point. The vehicle has been inspected by Capital Ford in Charlotte North Carolina. There has been a Ford customer experience associate assigned to the case who has reviewed the dealerships diagnostic of the issue. Ford has offered to pay for the part but not the labor required to install the part. There were no warning signs/lamps/indicators notifying of the underlying issue.

The contact owns a 2020 Ford Explorer. The contact stated that while driving at various speeds, the vehicle felt misaligned and made an abnormal rubbing sound. The vehicle was taken to the dealer, where the failure could not be duplicated; however, the dealer recommended the transmission be replaced. The manufacturer was notified of the failure and covered the transmission replacement. The dealer replaced the transmission. The contact stated that the failure persisted. The vehicle was taken back to the dealer, where it was test-driven, and the failure was duplicated; however, the dealer could not determine the cause of the failure. The vehicle was not diagnosed or repaired. The contact related to the failure of Ford Campaign Number: 24N01. The manufacturer was contacted, but no further assistance was provided. The failure mileage was unknown.

The contact owns a 2020 Ford Explorer. The contact stated while driving 35 MPH, the front passenger’s seat became detached. No warning light was illuminated. The vehicle had been diagnosed by the dealer and determined that the failure was due to a design flaw which cause the plastic clips used to hold the seat together had fractured. The vehicle was repaired several times, but the failure persisted. The manufacturer was made aware of the failure and advised the contact to contact the NHTSA Hotline for assistance. The failure mileage was approximately 35,000.

The contact owns a 2020 Ford Explorer. The contact stated that while driving with the auto-hold brake system engaged, the tires began to spin. The brake pedal was applied but the vehicle rolled and crashed into a vehicle. The charging system and engine warning lights were illuminated. There were no reported injuries, fire, or air bag deployment. A police report was filed. The vehicle was taken to the local dealer where it was diagnosed that the computer, AC unit, and wiring harness needed to be repaired. The vehicle was repaired but the failure recurred. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The approximate failure mileage was 32,000.

The contact owns a 2022 Ford Explorer. The contact stated while driving 55 MPH, the vehicle started to shake abnormally. While driving, the vehicle lunged forward without the accelerator pedal being depressed. There were no warning lights illuminated. The vehicle was taken to the local dealer, where it was diagnosed and determined that the transmission needed to be rebuilt. The software was reprogrammed and set for the parking brake to remain engaged. The vehicle was repaired, but the failure persisted. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The approximate failure mileage was 63,000.

My car warnings were malfunctioning as they were all flashing on briefly. The car has done this before and has other issues with the panel such as now it has the icon for camera visibility is not working. I cleaned each camera and the light is still on. I backed out of the driveway put the car in drive and started to accelerate. I stepped on the brakes and they were not working, I repeatedly tried to stop but they were gone. My car finally stopped (I was not far enough to have started to build any speed. I turned the car off and back on and the brakes were back on. This happened March 31st, 2022.

This has happened multiple times. Start the vehicle and put into drive while the brake pedal is fully depressed and the car will move forward. While it is in motion you can hear what sounds like the anti-lock system activating. You have to pump the brakes as I assume the master cylinder has lost pressure. It does this randomly and is not repeatable. If this ever happens and someone or another car is around it could be a very bad day.