2000 Ford F-350 Complaint Log

2000 FORD F-350 TIRE BLEWOUT CAUSING DAMAGES TO THE RIGHT FENDER AND MIRROR. *KB THE VEHICLE'S RIGHT FENDER, RIGHT MIRROR, BOTTOM RIGHT DOOR, WHEEL AND RIGHT SIDE RUNNING BOARD WERE DAMAGED. *NM *NM

IN THE PAST 2 WEEKS THE VEHICLE'S ENGINE STALLED DURING VERY INOPPORTUNE TIMES WHILE HIGHWAY DRIVING. FUEL HAS BEEN RULED OUT, A FULL SYSTEMS CHECK WAS PERFORMED BY THE DEALER, WITH NO ERROR CODES OR OTHER PROBLEMS NOTED. WHEN THE ENGINE BEGINS TO STALL, IT GOES THROUGH A PERIOD OF STUTTERING (<1 MIN) THEN STALLS COMPLETELY. YOU CAN WAIT FOR APPROX. 2-7 MINUTES AND THEN ENGINE WILL START AND OPERATE FOR A PERIOD OF <5 MINS, BEFORE AGAIN STALLING. DURING THIS SECOND EVENT, THE TRUCK NEEDED TO BE TOWED TO THE DEALER FOR FURTHER SERVICING. *NM

2000 FORD F350 V10 SPARK PLUG BLOWOUT. *JB

DT*: THE CONTACT STATED THAT THE TREAD OF THE VEHICLE'S FRONT PASSENGER TIRE SEPARATED FROM THE TIRE ITSELF WHILE TRAVELING 55 MPH ON A DRY AND FLAT COUNTY ROAD. THE TIRE WAS STILL INFLATED HOWEVER THE STEEL BELTS NEVER SEPARATED. THERE WAS NO VIBRATION NOTICED OR ABNORMAL BULGING TO THE TIRE PRIOR TO AND AFTER THE INCIDENT. THE TIRES ON THE VEHICLE WERE ROTATED REGULARLY AND CHECKED FOR CORRECT TIRE PRESSURE AS WELL.

DRIVING AT RATE OF 40 MPH WHEN I HAD TO SUDDENLY STOP FROM HITTING ANIMAL ON THE ROAD. BRAKE PEDAL WENT TO FLOOR WHEN PEDAL WAS SUDDENLY PRESSED. BRAKE LINE WAS BUSTED ON DRIVERS SIDE UNDERNEATH THE CLIP HOLDING BRAKE LINE. VEHICLE HAS NOT BEEN REPAIRED AS OF YET. *JB

3 CAM POSITION SENSOR FAILURES WITHIN APPROXIMATELY THE LAST 14 MONTHS. STEERING AND BRAKING ARE DIFFICULT AT BEST WHEN THE SUDDEN SHUTDOWN OF THE VEHICLE OCCURS. *NM

THE ENGINE WOULD JUST DIE EVEN WHILE DRIVING. THE CAMSHAFT POSTION SENSOR WAS BAD. *JB

TL* THE CONTACT OWNS A 2000 FORD F-350. THE CONTACT STATED THE HEADLIGHTS BECAME CLOUDY AND CAUSED THE LIGHTS TO APPEAR DIM. THE CONTACT WAS HAVING A HARD TIME DRIVING AT NIGHT. THE DEALER INSPECTED THE VEHICLE AND SUGGESTED THAT THE HEADLIGHT ASSEMBLY BE REPLACED. THE FAILURE MILEAGE WAS 65,000 AND THE CURRENT MILEAGE WAS 115,000. UPDATED 06/05/12 *BF

2000 FORD F350 7.3 THE TRUCK KEPT STALLING AND STOPPING IN TRAFFIC. HAD THE CODES CHECKED AND NOTHING SHOWED ON THE SCANNER, I WAS TOLD I HAD BAD FUEL. DRAINED THE TANK, CHANGED THE FUEL FILTER,PUT IN NEW FUEL FROM A DIFFERENT STATION AND THE TRUCK RAN FINE FOR A COUPLE OF DAYS AND THEN STOPPED AGAIN IN THE ROAD AND HAD TO HAVE IT TOWED. TOOK IT TO A FORD DEALER IN JOHNSTOWN THIS TIME. THE DEALER SAID THE CAM SENSOR WAS BAD AND FOR $ 680.00 THE PROBLEM WOULD BE REPAIRED. HAD THEM MAKE THE REPAIRS AND WHEN WE PICKED IT UP THE SERVICE WRITER SAID THIS HAPPENS ALL THE TIME. TALKED WITH SEVERAL OWNER OF THE DIESEL TRUCKS AND THEY TOLD ME THAT IT HAPPENS SO OFTEN THAT THEY KEEP A SPARE IN THE GLOVE BOX THAT IT ONLY TAKES 15 MIN TO CHANGE. THE FIRST TIME THIS HAPPENED I WAS ON A STATE RT AT RUSH HOUR WITH A SEMI PULLING OUT IN FRONT OF ME,HE SEEN THAT I WAS HAVING TROUBLE AND DID NOT CONTINUE. I WAS LUCKY THAT DAY. THE NEXT TIME IT HAPPENED I WAS GOING DOWN A STEEP HILL WITH A SHARP LEFT CURVE AT THE BOTTOM, JUST AS I GOT TO THE POINT OF HAVING TO USE MY BRAKES THE ENGINE STALLED, I MADE THE TURN BUT HAD TO DRIVE ON THE BERM AND IN THE DITCH TO DO SO. AGAIN WE RAN THE CODES AND NOTHING SHOWED. ON THE WAY HOME FROM SCANNING THE CODES IT STALLED IN THE MIDDLE OF ST RT 13 . THAT IS WHEN IT WENT TO THE DEALER FOR REPAIR. WHY KEEP MAKING THE SAME BAD SENSOR AND WHY DOES IT NOT SHOW UP WHEN YOUR RUN THE CODES? *NM

DT*: THE CONTACT STATED SINCE PURCHASE THE VEHICLE HAS A SHIMMY IN THE FRONT END PASSENGER SIDE. THIS OCCURS AT 35-45 MPH, WHEN THE TIRES HAVE AT LEAST 10,000 MILES WORTH OF WEAR. THE TIRE BRAND HAS BEEN CHANGED MULTIPLE TIMES AND THE TYPE OF TIRE DOES NOT AFFECT THE PROBLEM. THE VEHICLE HAS NOT BEEN TO A DEALERSHIP OR MECHANIC, BUT THE CONTACT REPLACED THE TIE ROD END TWICE, CENTER LINK, AND SPINDLE ON THE PASSENGER SIDE. THESE EFFORTS HAVE NOT CORRECTED THE PROBLEM.

I HAVE AN F350 DIESEL YEAR IS 2000. IN 2003 I HAD ENGINE-SENSOR FAILURE. FORD SAID IT WAS THE CAM SENSOR AND CHARGED APPROX. $400 TO REPAIR. THIS STARTED HAPPENING AGAIN IN FEB. 2006. I HAD PRIVATE REPAIR SHOP REPLACE CAMS, STILL STALLS,TOOK TRUCK TO FORD REPAIR, REPLACED GLOWPLUGS AND CHARGED SEVERAL HUNDRED DOLLARS, STILL HAVING TROUBLE. SEEMS TO BE WORSE IN MORNING AFTER NON USE FOR 12 HOURS. *NM

I HAD A CAM POSITION SENSOR FAIL ON THE FREEWAY I-80 (RENO) ON MY 2000 FORD F350 POWER STROKE DIESEL PICK-UP. REPLACED PART OUT OF POCKET. NO OTHER ISSUES LEADING UP TO THE FAILURE. TRUCK STOPPED DEAD IN ITS TRACKS. *TR

FRONT BRAKES, FADE AND EXTENDED STOPPING DISTANCE; THERE ARE FLOAT PINS WHICH KEEP THE CALIPERS CENTERED OVER THE ROTORS . THEY HAVE SEIZED UP. THE VEHICLE BREAKING WAS BECOMING SLUGGISH. REPEATED INSPECTION OF THE FRONT BRAKE PADS INDICATED THEIR CONDITION TO BE GOOD. EVENTUALLY I DECIDED TO ORDER NEW CALIPERS WITH PADS. THESE UNITS CAME WITH 'NEW FLOAT PINS'. MUCH TO MY SURPRISE MY CALIPERS WERE GOOD BUT THEY WERE LOCKED IN POSITION BECAUSE OF THE SEIZED FLOAT PINS. WHEN THE BRAKES WERE APPLIED THE PRESSURE WAS TO THE INSIDE PAD ONLY GREATLY LENGTHENING THE STOPPING DISTANCE. AS THE PROBLEM CAME ON GRADUALLY I DIDN'T REALIZE HOW POOR THE BRAKING HAD BECOME UNTIL I REBUILT THE SYSTEM. THE PINS WHICH NEED TO SLIDE FOR PROPER BRAKING HAVE LITTLE RUBBER BOOTS TO KEEP OUT ROAD DEBRIS AND WATER. THESE BOOTS WERE NOT SEATED ON THE GROVE ON THE ORIGINAL CALIPER BODY. AS THE SYMPTOMS COME ON GRADUALLY THERE ARE OTHER VEHICLES OUT THERE WITH SEVERELY DEGRADING BRAKE PERFORMANCE. CURIOUSLY THE REPLACEMENT CALIPERS HAD A BAG OF SPARE PARTS. *NM

ON DEC 20TH, 2005 I WAS DRIVING ON I-35 AT HIGHWAY SPEED WHEN I STARTED HEARING MULTIPLE POPPING SOUNDS ON THE FRONT OF THE ROOF OF MY FORD F-350 XLT LARIAT LE. A FRIEND WAS WITH ME AT THE TIME AND HE FIGURED OUT WHAT THE SOUND WAS WE PULLED OFF AT THE NEXT EXIT AND HE WAS RIGHT. THE WINDSHIELD VISOR MOUNT WHICH WAS FACTORY INSTALLED AND SPOT WELDED TO THE VEHICLE AT THE KENTUCKY FORD FACTORY, HAD CAME LOOSE FROM THE VEHICLE. AFTER THIS INCIDENT I TOOK IT TO A BODY SHOP TO HAVE THEM LOOK AT IT AND THEY STATED THAT THE SPOT WELDS THE FACTORY DID AT THE TIME OF THE BUILDING OF THE TRUCK DID NOT HAVE A HIGH ENOUGH HEAT SETTING TO MAKE A GOOD FUSION OF THE METAL FOR A PROPER WELD. I'VE TAKEN THE TRUCK TO 2 FORD DEALERS AND WAS TOLD BY BOTH THAT THIS WAS NOT COVERED DUE TO THE TRUCKS FACTORY WARRANTY OF 3 YEAR 36,000 MILES BEING OVER. THERE ARE 4 FACTORY HOLES IN THE ROOF OF THE TRUCK THAT ARE UNCOVERED DUE TO THE FACTORY VISOR NOT BEING IN PLACE WHICH ALLOWS RAIN AND WEATHER TO ENTER THE TRUCK. *JB

2000 F350 TIRE BLEW OUT. *TS WHEN THE TIRE BLEW OUT, THE CONSUMER LOST CONTROL OF THE VEHICLE, WENT THROUGH A MEDIAN INTO A DITCH AND SUBSEQUENTLY THE TRUCK TURNED OVER. *JB

WHILE TRYING TO BRAKE AT ANY TIME THE VEHICLE STEERING LOCKS UP (THE PUMP DOES NOT SUPPORT THE PRESSURE FOR THE BRAKES AND STEERING). AFTER CONTACTING SEVERAL MECHANICS THIS IS A FORD DIESEL COMMON PROBLEM AND THERE HAS NOT YET TO BE A CORRECT FIX. *JB

WHEN UP-SHIFTING GEARS, THE SERVICE ENGINE LIGHT WOULD ILLUMINATE AND ACCELERATOR IS NON-RESPONSIVE AS ENGINE IDLES AROUND 1K RPM CAUSING LOSS OF MOMENTUM. AFTER A FEW SECONDS, THE ACCELERATOR CAN BE USED TO INCREASE SPEED, BUT DEPRESSING THE CLUTCH STARTS THE CYCLE OF NON-RESPONSIVE ACCELERATOR ACTION ALL OVER. THE TRUCK HAS DIED ON CURBS, IN INTERSECTIONS, AND WHILE GETTING ONTO ON RAMPS. FORD HAS REPLACED SOME MAGNETS WHICH JUST DELAYED THE ACTION FOR A FEW WEEKS. THE LONGER IT GOES WITHOUT REPAIR, THE WORSE IT BECOMES. *NM

I'VE HAD TWO SEPARATE CPS FAILURES ON MY 2000 FORD SUPER DUTY WITH THE 7.3 DIESEL. BOTH TIMES IT MANIFESTED ITSELF AS THE MOTOR DYING WITHOUT WARNING. ONCE IT WAS ON THE HIGHWAY. THERE WHERE NO INJURIES WITH EITHER INCIDENT BUT THAT COULD HAVE EASILY BEEN A DIFFERENT STORY HAD I BEEN PULLING MY TRAILER. BOTH TIMES REPLACING THE (OVER PRICED) CPS WAS THE SOLUTION. THE OLD PARTS WERE DISCARDED.*JB

DT*: THE CONTACT STATED WHEN THE BRAKE PEDAL WAS DEPRESSED; THE BRAKE PEDAL WENT TO THE FLOOR. THE VEHICLE WAS TAKEN TO THE LOCAL DEALERSHIP FOR INSPECTION AND REPAIR. THE SERVICE PERSONNEL DISCOVERED THE BRAKE LINE WAS FRACTURED DUE TO CORROSION.

ON MY 2000 FORD F350 DIESEL, THE CAMSHAFT POSITION SENSOR FAILED AS I WAS ENTERING THE HIGHWAY. THE ENGINE STALLED AND I HAD NO POWER TO THE ENGINE. THE POWER STEERING AND POWER BRAKES FAILED AND I COULD NOT GET THE TRUCK TOTALLY OFF THE HIGHWAY. LUCKILY A POLICE OFFICER ON THE HIGHWAY PULLED IN BEHIND ME AND STAYED WITH ME WITH HIS LIGHTS ON UNTIL A TOW TRUCK ARRIVED. IT WAS A SCARY SITUATION. THEN I FIND OUT THAT THE PROBLEM IS VERY COMMON, VERY DANGEROUS, AND VERY IGNORED BY THE MANUFACTURER. IF THE POLICE OFFICER WAS NOT THERE QUICKLY, OR IF HE HAD A CALL TO ATTEND TO, SOMEONE COULD HAVE BEEN KILLED. *JB

DT: THE CONTACT SAID THE VEHICLE WAS SHUTTING OFF WHILE DRIVING DUE TO CAM SHAFT SENSOR FAILURE. THE ENGINE DIED IN THE MIDDLE OF MAKING A RIGHT TURN. HE ALMOST HIT ANOTHER VEHICLE, TO MISS THE OTHER VEHICLE HE WENT OVER AN EMBANKMENT. AFTER THE INCIDENT THE VEHICLE WAS TOWED TO A FORD DEALERSHIP. THEY DIAGNOSED THE PROBLEM AS THE CAM SHAFT SENSOR. THE CAM SHAFT SENSOR WAS REMOVED AND REPLACED WITH A NEW ONE. THE REPAIR WAS MADE AT THE CONTACT'S EXPENSE AS FORD OFFERED NO FREE REMEDY. *AK UPDATED 12/7/2005. THE CONSUMER REQUEST REIMBURSEMENT FOR THE COST OF A NEW CAM SENSOR AND TOW TRUCK SERVICE (PART # F7TZ12K073-A, SYNCRO 997690). *NM

ON SEPTEMBER 30, 2005 I EMAILED FORD MY CONCERN WITH THE POWER STEERING HOSE FAILURE ON MY 2000 F350 TRUCK ([XXX], 153,440 KM). I SUBSEQUENTLY SPOKE TO THEIR CUSTOMER SERVICE REPRESENTATIVE, AND TO THE SUPERVISOR IN THAT DEPARTMENT, AND COULD NOT BELIEVE THE RUN-AROUND I RECEIVED REGARDING MY CONCERN. THEY CLAIMED THEY HAD NO ACCESS TO PERFORMANCE RECORDS ON VEHICLES AND COULD NOT COMMENT ON MY CONCERN. THEY SIMPLY TRIED TO BOUNCE ME BACK TO THE DEALER, WITH WHOM I HAD ALREADY DISCUSSED MY CONCERN. THE DEALER ADVISED I COMMUNICATE WITH FORD'S CUSTOMER SERVICE DEPARTMENT AND PROVIDED ME WITH THE EMAIL ADDRESS. HERE IS WHAT HAPPENED. WHEN BACKING OUT OF MY DRIVEWAY, THE POWER STEERING AND POWER BRAKES FAILED, LEAKING POWER STEERING FLUID ALL OVER THE DRIVEWAY. HAD THE VEHICLE TOWED TO JUBILEE FORD IN SASKATOON, SASKATCHEWAN FOR REPAIR. THE HIGH PRESSURE LINE TO THE HYDRO-BOOST WAS REPLACED AT A COST OF $292.70. I WAS TOLD THE NUT AT ONE END OF THE HOSE FAILED. I KEPT THE OLD HOSE. MY CONCERN IS VERY SIMPLE. BECAUSE OF THE VERY SERIOUS CONSEQUENCE OF THIS (LOSING STEERING AND BRAKE CONTROL) HAPPENING WHILE DRIVING (IE. ACCIDENT CAUSING INJURY OR DEATH), HAS THIS OCCURRED WITH OTHER SUPER DUTY TRUCKS AND SHOULD THERE BE A RECALL FOR THIS FAILURE? FORD'S ENGINEERING DEPARTMENT MUST KEEP RECORDS OF THIS TYPE OF FAILURE, AS IT APPLIES TO 1999-2005 SUPER DUTY TRUCKS, AND HENCE FORD SHOULD BE ABLE TO PROVIDE A STRAIGHT FORWARD ANSWER. I HAVE NOT BEEN ABLE TO OBTAIN THIS FROM THEM. *NM UPDATED 07/18/2012 *JS INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I EXPERIENCED A COMPLETE BRAKE LINE FAILURE AND LOSS OF BRAKE USE ON MY 2000 FORD F350 SUPER DUTY 4X4 PICKUP. LUCKILY, THE FAILURE OCCURRED WHILE MY VEHICLE WAS BEING INSPECTED BY THE STATE OF NEW JERSEY. I HAD TO HAVE IT TOWED TO THE NEAREST FORD DEALERSHIP WHERE THEY PROCEEDED TO BILL ME EXTENSIVELY FOR REPLACING THE MAIN BRAKE LINE. *JB

DT: THE CONTACT STATED VEHICLE TURNED OFF WHILE DRIVING. IT JUST DIED. IT VARIED AT THE SPEEDS THAT THE CONTACT WAS GOING. THE DEALER CHANGED VARIOUS SENSORS. THEY COULD NOT DUPLICATE THE PROBLEM. THEY HAVE REPAIRED THE WIRING HARNESS. ON 9-16-05 THE CONTACT TOOK VEHICLE TO THE DEALER, AND THE DEALER REPLACED THE WIRING HARNESS. HOWEVER, THEY WERE STILL EXPERIENCING THE SAME PROBLEMS WITH THE VEHICLE JUST STOPPING. IT WILL SOMETIMES START BACK RIGHT AWAY. SOMETIMES IT WILL JUST NOT START, AND ONE COULD WAIT 10 MINUTES AND IT WILL RESTART OR MAY HAVE TO WAIT 2 HOURS BEFORE IT WILL RESTART. THIS HAS BEEN AN ONGOING PROBLEM FOR TWO YEARS. THE CONTACT CITED RECALL 05S34 ON THE SAME VEHICLE BUT JUST DIFFERENT YEAR MODELS. *AK

DT: WHILE DRIVING , THE CO NSUMER NOTICED THE ODOMETER WAS NOT WORKING. NO PARTICULAR SPEED WAS NOTICED AT WHICH THIS HAS OCCURRED. CONSUMER DID NOTE IT WORKS WHEN STOPPED AT A RED LIGHT THEN ACCELERATING PAST THROUGH THE RED LIGHT THE ODOMETER BEGAN TO WORK AGAIN AFTER A COMPLETE STOP BUT THIS WAS INTERMITTENT. *AK *JB

DT: 2000 FORD F350. THE CONSUMER STATED WHEN DRIVING AT 55 MPH THE SPARE TIRE CABLE BROKE AND LOST THE SPARE TIRE. THERE WAS NO ONE BEHIND CONSUMER'S VEHICLE AND NOBODY WAS INJURED. THE VEHICLE HAS NOT BEEN FIXED. THE SPARE HAS NEVER BEEN TAKEN OFF OF THE VEHICLE.*AK

MY F-350 PICKUP DOES NOT HAVE A LABEL ON THE DRIVER DOOR SO I HAVE NO WAY OF KNOWING THE PROPER TIRE INFLATION FOR THE VEHICAL. THE TIRES ARE RATED FOR UP TO 80 PSI, BUT BOTH THE TIRE AND VEHICAL MANUALS STATE THAT IT SHOULD BE BASED ON THE LABEL ON THE DRIVERS DOOR. FORD SAYS THEY CAN NOT PROVIDE THAT INFORMATION TO ME BECAUSE THEY DON'T HAVE IT- ALTHOUGH APPERANTLY A DEALER COULD GET IT. DRIVING A TRUCK THAT COULD REQUIRE 75 PSI IN THE TIRES WITH ONLY 30 PSI COULD RESULT IN A FAILURE AT HIGHWAY SPEEDS, BUT THE FORD REP I SPOKE TO JUST KEPT SAYING THEY COULDN'T HELP ME.

DT: THE STEERING SHAFT (POWER STEERING GEAR BOX OUTPUT SHAFT) SNAPPED OFF WHILE APPROACHING A STOP SIGN AT ABOUT 35 MPH. WHEN THIS HAPPENED THE VEHICLE DID STOP WITH NO ACCIDENT. I AM IN THE PROCESS OF FIXING THIS PROBLEM. *TT

MY F350 DIESEL 4X4 HAS THE STEERING SHUT DOWN IN TRAFFIC, SEEMS LIKE THE POWER STEERING PUMP IS ALSO THE ABS BRAKE BOOSTER. WHEN THE BRAKES ARE APPLIED THE STEERING ASSIST STOPS. WITH THE WEIGH OF THE DIESEL ENGIN IT IS IMPOSSIBLE TO TURN THE STEERING WHEEL MORE THAN A QUARTER TURN WHEN THE BRAKE IS APPLIED. I NEED TO ROLL SEVERAL FEET WITHOUT BRAKE APPLIED IN ORDER TO TURN, PUMP REPLACED @ 20K MI NO BETTER. THE SITUATIONS IS GETTING WORSE...NO SOLUTION IN SIGHT

WHILE DRIVING AT A REDUCED SPEED ON THE INTERSTATE FREEWAY, BECAUSE OF RAIN, I STARTED TO EXPERIENCE A VIBRATION FROM THE TIRES. AT THE FIRST OPPORTUNITY I PULLED OFF INTO A REST AREA TO CHECK THE TIRE PRESSURE THINKING THAT I HAD A TIRE THAT WAS GOING FLAT. I MEASURED THE AIR PRESSURE IN ALL 4 TIRES ON MY 2000 FORD F-350. I MEASURED 60LBS IN THE FRONT AND 70LBS IN THE REAR. I INSPECTED THE WHEELS TO SEE IF THERE WAS ANY APPARENT PROBLEM WITH THE TIRE BUT I COULDN?T FIND ANYTHING. I DEDUCED THAT THE VIBRATION MIGHT BE A RESULT OF THE TIRE THROWING A BALANCING WEIGHT AND I DECIDED TO CONTINUE ON MY JOURNEY SINCE I COULDN?T FIND ANY PROBLEM. ABOUT 8 MILES FURTHER UP THE ROAD I SUFFERED A TREAT SEPARATION FROM THE TIRE WHICH CAME ACTUALLY CAME OFF THE TIRE. THE TIRE DID NOT LOSE AIR IMMEDIATELY AS A RESULT OF THE FAILURE (IT DID HAVE A SLOW LEAK THAT DRAINED THE TIRE AFTER ABOUT 6 HOURS). I WAS ABLE TO MAINTAIN CONTROL OF THE VEHICLE THROUGH THE ENTIRE INCIDENT AND COULD SAFELY DRIVE IT UNTIL I COULD FIND A SAFE PLACE MILE FURTHER UP THE ROAD WHERE I REPLACED THE DAMAGED TIRE. THE RESULTING INCIDENT DAMAGED THE FENDER AREA OF MY VEHICLE AND WILL REQUIRE PROFESSIONAL REPAIR. AS I MENTIONED EARLIER I WAS DRIVING AT A REDUCED SPEED FOR THIS SECTION OF THE INTERSTATE FREEWAY BECAUSE OF HEAVY RAIN AND AT NO TIME DID MY SPEED EXCEED 60MPH. THE AIR TEMPERATURE FROM THE TIME I FIRST NOTICED THE PROBLEM UNTIL THE FAILURE WAS 43 TO 38 DEGREES. *AK

AFTER ABOUT FOUR YEARS OF GOOD SERVICE A PROBLEM STARTED AND NOW STILL HAVING NUMEROUS CAMSHAFT POSITION SENSOR(CPS) FAILURE IN THE 2000 F350 7.3 SD PICKUP TRUCK CPS SYSTEM. DEALERSHIP AND LOCAL AUTOMOTIVE REPAIRS HAVE BEEN PERFORMED AS EXTRA COSTS TO CORRECT THE PROBLEM.THE ORIGINAL CPS PART NUMBERS ARE NOT AVAILABLE AND AN ALTERNATE PART IS A REPLACEMENT TODAY. A YEAR AFTER THE LAST REPAIR OF THE SAME SYMPTOMS THE COMPUTER CODE FINALLY RECOGNIZED THE DEFAULT WITH A CODE P0340. THIS IS THE FIRST TIME THE SENSOR ERROR WAS IDENTIFIED BY THE CHECK ENGINE CODE SYSTEM AND IT IS THE SECOND TIME THE CPS WILL BE REPLACED. I HAVE SPENT OVER $1,500 IN REPAIRS TO FIND A FIX. I HOPE THE NEW PART BE THE FINAL FIX. *TR

WHILE DRIVING AT APPROXIMATELY 40 MPH CONSUMER'S VEHICLE WAS INVOLVED IN A HEAD ON COLLISION WITH ANOTHER VEHICLE. UPON IMPACT, THE SEAT BELT FAILED TO RESTRAIN THE DRIVER CAUSING THE DRIVER TO HIT THE WINDSHIELD. DRIVER SUSTAINED INJURIES. *AK

WHILE DRIVING 5-70 MPH CONSUMER LOST POWER STEERING/BRAKING. CONSUMER MANAGED TO PULL OVER, AND HAD THE VEHICLE TOWED. DEAALERSHIP REPAIRED THE POWER STEERING AND BRAKE COMPONENTS, BUT THE CONSUMER WAS STILL HAVING THE SAME PROBLEMS. *AK

PURCHASED TIRES FROM COSTCO FOR THE BACK OF MY PICKUP. THEY PLACED 82.5 PSI IN THE REAR TIRES OF A EMPTY PICKUP...AS DIRECTED BY MICHELIN. THIS CREATED A VERY SERIOUS SAFETY ISSUE AS THE TRUCK DID 3 REVOLUTIONS DOWN THE FREEWAY DUE TO SEVERELY CROWNED TIRES. SOMEONE HAS TO STOP THIS RECOMMENDATION OR SOMEONE IS GOING TO BE HURT/KILLED. THIS IS A COMMON SENSE ISSUE THAT NEITHER COSTCO OR MICHELIN WILL ADDRESS. I WOULD LIKE A RESPONSE TO THIS EMAIL IF POSSIBLE. THIS PRACTICE HAS TO BE STOPPED, PLEASE REVIEW WITH YOUR ENGINEERS. THANK YOU DON PREUITT. *JB

WHILE THE VEHICLE WAS PARKED A FIRE STARTED UNDER THE HOOD. THE VEHICLE WAS TOTALED. THE MANUFACTURER WAS NOTIFIED, BUT DID NOT RESOLVE THE PROBLEM. *AK

THE CONSUMER WAS INVOLVED IN A FRONTAL COLLISION WITH A ELEVATED CRANE PILLAR WHILE DRIVING 20-30 MPH AND NEITHER AIR BAG DEPLOYED. THE DRIVER AND THE PASSENGER WERE BOTH RESTRAINED IN THEIR SEAT BELT. THE DRIVER RECEIVED MINOR INJURIES, BUT THE PASSENGER WAS TRANSPORTED TO THE LOCAL HOSPITAL BY AMBULANCE DUE TO HEAD INJURIES. THE DEALER WAS NOT NOTIFIED. *JB

BOTH PASSENGER AND DRIVERS SIDE AXLE SEALS ON FRONT REAR ARE HANGING OUT OF END OF AXLES. DRIVERS SIDE IS LEAKING OIL.DEALER ALREADY REPAIRED THIS PROBLEM ONCE AT 30K NOW IT IS MY COST PARTS COUNTER SAID FORD REDESIGNED SEALS BECAUSE OF SO MANY PROBLEMS

I HAVE A 2000 FORD F-350 . I BOUGHT IT USED 6 MONTHS AGO. I RECENTLY HAD THE FRONT RIGHT TIRE LOSING AIR. UPON INSPECTION BY MY MECHANIC, IT WAS DETERMINED THAT THE ALLOY RIM HAD A STRESS CRACK IN IT. UPON CONTACTING FORD, THEY SAID THERE WAS NO RECALLS AND I WOULD HAVE TO REPLACE IT AT MY EXPENSE. I HAVE THE OLD RIM AND DIGITAL PICTURES OF IT ALSO. THIS WHEEL WAS NOT DAMAGED IN ANY WAY, AND THE CRACK SEEMS TO BE FROM A DEFECTIVE DESIGN. THE RIM DID NOT FAIL, BUT HAD I NOT NOTICED THE LOW AIR PRESSURE IN THE TIRE, IT MAY HAVE SOON FAILED. THANK YOU IN ADVANCE, ROBERT POWELL. *JB

THE CLUTCH FAILED TO ENGAGED WHEN APPLIED. THE CONSUMER NOTICED THAT THE CLUTCH WOULD ENGAGED ON ITS OWN. THE CONSUMER WAS ABLE TO DRIVE IT TO THE DEALER FOR INSPECTION. THE MECHANIC WAS UNABLE TO DUPLICATE THE PROBLEM. JB.....CONSUMER STOPPED AT A TRAFFIC LIGHT WITH THE CLUTCH PEDAL FULLY DEPRESSED WHEN THE VEHICLE LURCHED FORWARD TOWARDS THE CROSSWALK NARROWLY AVOIDING PEDESTRIANS. THE CLUTCH PEDAL WA SFUKKY DEPRESSED. CONSUME RHAD TO SHUT OFF THE IGNITION SWITCH TO STOP THE VEHICLE. CONSUME RTOOK THE VEHICLE TO FREEDOM FORD FOR REPAIRS AND WAS PERENTED WITH A BILL FOR $520.34. CUSTOMER SERVICE REPRESENTATIVE TOLD CONSUMER THAT REPAIRS WERE NOR COVERED UNDER WARRANTY SINCE THE CLUTCH IS NOT PART OF THE POWER TRAIN. *AK

VEHICLE WAS TRAVELING ABOUT 30 MPH WHEN ALL OF A SUDDEN THE BRAKES DID NOT WORK. THERE WAS BRAKE FLUID SPILLING, AND THE EMERGENCY BRAKE WAS APPLIED, BUT IT WAS STILL DIFFICULT FOR THE VEHICLE TO COME TO A COMPLETE STOP.*AK

RECALL ALREADY DONE ON OCTOBER 29, 2002 FOR WIPER MOTOR. ON NOVEMBER 12, 2004 I STARTED THE TRUCK UP AND A MINUTES LATER I LOOKED AND SAW SMOKE COMING FROM THE UNDERNEATH THE HOOD AND THE WIPERS RUNNING ALL BY THEMSELVES IN THE PARKED POSITION, THE WIPER MOTOR MALFUNCTIONED AGAIN. IT WAS TOWED TO THE DEALERSHIP AFTER CALLING THEM. TOTAL REPLACEMENT COVERAGE IS UNKNOWN AND DAMAGE IS UNKNOWN AT THIS TIME. *JB

CONSUMER'S VEHICLE WAS INVOLVED IN A HEAD ON COLLISION AT 55 MPH, IMPACTING A HEARD OF COWS. ONE OF THE COWS ENDED UP IN THE ENGINE. UPON IMPACT, DRIVER'S SIDE AIR BAG FAILED TO DEPLOY. NO INJURIES WERE SUSTAINED DUE TO THE OCCUPANTS WEARING SEAT BELTS.*AK

FRONT SUSPENSION FRONT OF VEHICLE SHAKES VIOLENTLY WHEN BRAKING, OR WHEN VEHICLE HITS A BUMP SMALL OR LARGE. TAKEN FOR REPAIRS REPAIRED AND REPLACED TIRES,BRAKES, IDOL ARMS NOTHING SEEMS TO SOLVE THE PROBLEM. HAVE 4 F350'S AND ALL DO THE SAME. E350'S NO PROBLEM. DEALER NO HELP IN SOLVING THE ISSUE. *JB

THE BRAKE LINE HAD RUSTED . AS A RESULT, THE BRAKES FAILED. NO IMPACT REPORTED. *JB ALL THE OTHER LINES INCLUDING THE FUEL LINES WERE RUST FREE. *SC *JB

REAR TIRE FAILED. UPON REVIEW THE REAR LEAF SPRING BROKE AND WAS DISPLACED TO THE POINT OF RIPPING OUT THE INNER SIDE WALL OF THE TIRE. AT THE TIME I WAS RUNNING ABOUT 70 MPH IN WEEKEND HIGHWAY TRAFFIC. *AK

FORD F350 SUPER DUTY CREW CAB: WHILE DRIVING THE INNER AND OUTER AXLE BEARING SEALS BLEW OUT, ALONG WITH THE HUB BEARING ON THE FRONT DRIVERS SIDE. THE WHEEL TURNED IN AND APPEARED AS IF IT WOULD COME OFF. UPON INSPECTION, THE PASSENGER SIDE INNER AND OUTER SEALS WERE ALSO HANGING OUT. CONTACTED FORD AND THEY SAID THAT THERE WAS NO RECALL OR SERVICE BULLETIN ON THE TRUCK. THEY WILL NOT HELP OUT IN ANY WAY. THERE IS ANOTHER REPORT ON THIS WEB SITE OF THE SAME INCIDENCE. OUR FRIEND WHO OWNS THE SAME YEAR F350 CHECKED HIS TRUCK TO FIND THE EXACT PROBLEM, THE SEALS ON THE AXLE BEARINGS ARE HANGING OUT!

FIRESTONE STEELTEX AT LT265/75R16 LOAD RANGE E. DOT# VNW81XL020. THE TIRE HAD 48,854 MI OF TREAD WEAR. THE CONSUMER EXPERIENCED TREAD SEPARATION. THE TIRE DID HOLD AIR. THERE WAS ALSO DAMAGE TO THE RIGHT REAR QUARTER PANEL OF THE VEHICLE. . *JB

VEHICLE HAD TWO TANKS. FIRST TANK WOULD EMPTY INTO THE SECOND TANK. THIS CAUSED A GASOLINE SPILLED ONTO THE GROUND. CONSUMER WAS ABLE TO DRIVE VEHICLE TO THE DEALER, AND MECHANIC DETERMINED THAT TANK' NEEDED TO BE REPLACED. *AK GAS LEAK SEE RECALL 93V125. *TC

CONSUMER'S VEHICLE WAS INVOLVED IN A FRONTAL COLLISION. UPON IMPACT, BOTH FRONTAL AIR BAGS FAILED TO DEPLOY. DRIVER SUSTAINED MINOR INJURIES. VEHICLE WAS TOWED TO THE DEALER FOR INSPECTION. *AK

WHILE DRIVING 45 MPH CONSUMER APPLIED THE BRAKE PEDAL AND THE BRAKES FAILED, CAUSING CONSUMER'S VEHICLE TO COLLIDE WITH THE VEHICLE IN FRONT. DRIVER SUSTAINED MINOR INJURIES, AND VEHICLE WAS TOWED TO THE DEALER FOR INSPECTION. *AK