2020 Ford Fusion Complaint Log

The flexplate in my 2020 Ford Fusion SE (1.5L EcoBoost engine) failed at just over 53,000 miles. The car began making loud knocking and rattling noises while driving, and it vibrated heavily at idle and during acceleration. This posed a serious safety concern, as we feared the car could stall or break down while on the road with our toddler in the backseat. We took it to an independent, certified repair shop where they diagnosed a broken transmission flexplate, which required immediate replacement. The repair cost nearly $3,000, and the shop confirmed it was not caused by driver error or normal wear-and-tear. The failure was premature and mechanical in nature. The mechanic informed us that this specific engine and flexplate design have been recalled before in other Ford models using the same 1.5L EcoBoost engine and parts. They suggested we contact Ford, as this appeared to be a known defect that should be covered under goodwill or extended warranty. We followed their advice and reached out to Ford directly, but Ford refused to offer any assistance — even though they are aware of these ongoing flexplate failures across similar vehicles. After researching, I discovered Ford has had multiple flexplate and powertrain-related recalls in other 1.5L and 1.6L EcoBoost engines in previous model years. I also found many online complaints from other Ford owners experiencing the same flexplate failures, often at similar mileage. Yet, this issue has not been acknowledged or recalled for the 2020 Ford Fusion SE. This is clearly a design or manufacturing flaw that should be investigated by the NHTSA. Flexplate failure puts lives at risk and results in major repair bills for consumers. Please investigate this ongoing issue before someone is seriously hurt.

The contact owns a 2020 Ford Fusion. The contact stated while driving 25 MPH, the vehicle failed to accelerate as intended while depressing the accelerator pedal. The check engine warning light was illuminated. The contact stated there was an abnormal sound coming from the engine. The vehicle as taken to the dealer; however, no cause for the failure was found. The cam shaft sensor was replaced; however, the failure persisted. The contact stated that on another occasion, while driving 8 MPH, the engine seized. The message "See Manual" was displayed. The vehicle was taken to an independent mechanic but was not diagnosed or repaired. The vehicle was taken to several dealers and independent mechanics. The contact was recently informed that the engine needed to be replaced. The vehicle was not repaired due to the cost. The manufacturer was not notified of the failure. The failure mileage was approximately 152,000.

Component or system that failed: Flex plate, engine electrical system, and alternator (possible related failures). The issue has been diagnosed by a licensed mechanic and is available for inspection upon request. Incident Description: On April 15, 2025, while driving my 2020 Ford Fusion SE 1.5L Turbo, the vehicle suddenly experienced a total power failure. The check engine light began flashing, and the battery light blinked rapidly. Within seconds, the engine shut down completely while I was mid-drive in traffic, leaving me stuck and unable to move for over 20 seconds. This was a terrifying and dangerous situation that nearly put my life at risk. I was eventually able to restart the vehicle, but it began shaking and rumbling violently — worse than ever before. This issue was never present before my car was involved in two separate collisions, where both other drivers were found 100% at fault. The vehicle was repaired at Fix Auto Santee (a USAA-assigned body shop), but they failed to inspect internal components. A licensed mechanic at J&L Auto Care later confirmed a broken flex plate and advised it was unsafe to drive. This problem has not been addressed or fixed by the responsible insurers (USAA and AAA) or the body shop. It has progressively worsened and now created a life-threatening situation. Warning lamps or symptoms before failure: A rattling and vibrating noise began immediately after I picked up the car from the body shop in March 2025. No lights were initially present. The electrical and engine lights only appeared on April 15 when the engine shut down mid-drive. Inspected by: •Independent service center (J&L Auto Care, diagnosed flex plate failure) •USAA and AAA were informed but refused to cover or further inspect the damage •Fix Auto Santee heard the issue but refused to inspect, citing body-only service Problem available for inspection: Yes — vehicle is currently undrivable and available for full inspection.

The contact owns a 2020 Ford Fusion. The contact stated that while reversing from the residence, the vehicle suddenly stopped and shifted into park. The contact shifted to reverse, but the gear shifter independently shifted back to park. The contact stated that the vehicle failed to shift to the intended gear. The transmission shifter and the see the owner’s manual messages were displayed. There was a WRENCH symbol displayed. The contact stated that the failure was related to NHTSA Campaign Number: 22V413000 (Power Train); however, the VIN was not included. The contact called the local dealer, who confirmed that there were no recalls on the VIN. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline, but no additional assistance was provided. The failure mileage was approximately 79,127.

The contact owns a 2020 Ford Fusion. The contact stated that upon starting the vehicle, the vehicle hesitated while responding. The contact stated that while driving at an undisclosed speed, the vehicle lost motive power, with an abnormally loud vibration coming from the engine. There was no warning light illuminated. The vehicle was taken to a local dealer, where the vehicle was diagnosed, and the contact was informed that either the flywheel or the flex plate was faulty and needed to be replaced. The vehicle was not repaired. The contact referenced Customer Satisfaction Program: 22N12 as the possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 103,000.

The contact owns a 2020 Ford Fusion. The contact stated that after starting the vehicle there was an abnormally loud knocking sound coming from the engine compartment. The vehicle was taken to the local dealer who diagnosed that the flex plate was cracked and needed to be replaced along with the torque converter, the transmission fluid pump, and seals. The vehicle was repaired. The manufacturer was notified of the failure and informed the contact that the vehicle was no longer eligible for a Customer Satisfaction Campaign related to the failure. The failure mileage was 122,000.

The contact owns a 2020 Ford Fusion. The contact stated that while driving at various speeds, the vehicle was driving rough. The contact stated that the vehicle hesitated while accelerating with a whining sound coming from the transmission. The cause of the failure was not yet determined. The local mechanic was notified of the failure and informed the contact that the transmission was faulty and needed to be replaced. The manufacturer was contacted and informed of the failure; however, no assistance was provided. The local dealer was not contacted. The failure mileage was 100,000.

My flex plate is cracked making the car unsafe to drive there are recalls on other years and vehicles with the same engine and power train and same flex plate as mine but my vin# says no recall I find it interesting that they can justify not replacing a known faulty part. The campaign 22N12 covers other 2020 ford fusions

The contact owns a 2020 Ford Fusion. The contact stated that while driving approximately 35 MPH, the message "Engine Coolant Over-Temperature" was displayed, and the temperature gauge warning light illuminated. The contact pulled over to the side of the road and turned off the vehicle. The vehicle was restarted after 20 minutes. The vehicle was taken to the residence. The vehicle was towed to a dealer, where it was diagnosed and determined that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 132,000.

I have had 2 transmissions within the last year, making this the third Transmission on my vehicle. I had to have another common issue with the car replaced, which is a purge valve. My ABS light goes off often causing difficulty to steer the car and warning lights are activated showing that the safety features are not available. Lastly, there is a crack in the engine block caused by coolant in the spark plug due to overheating. This engine issue is one with the engines that Ford is aware of but I do NOT see a recall. The engine is blown due to this design and the warranties do NOT cover it. Case number [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My 2020 Ford Fusion has had multiple transmission failures and has now had a third transmission installed. The newest issue with with the engine design that Ford is aware of but is not covered by extended warranty. The engine block is cracked due overheating caused by coolant intrustion and flexplate problems. Each time these incidents were identified and examined by Ricart Ford in Columbus, OH. The car was also purchased by the same dealer in January of 2024. The check engine light along with the temperature light were triggured by the engine issue on [XXX] I immediately contacted Protective(My warranty company) and requested that the car be transported to Ricart. I also contacted the service deparment at Ricart and explained the issue. There was plenty of coolant in the resevoir but the coolant leaked into the cylinders and caused the car to overheat. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6

The manufacturer is using the wrong material for the parts on my car. Currently, the right-side lower control bushing is bulging out because a steel bushing was used instead of the aluminum one specified on the website. This issue is causing my car to pull to the right, making steering difficult. I've also experienced the same problem on the left side in the past. I request a recall to fix this and ensure the safety of all drivers on the road.

The contact owns a 2020 Ford Fusion. The contact stated that after starting the vehicle, while the vehicle was idling, there was an abnormal knocking sound coming from the engine. There was no warning light illuminated. The vehicle was taken to two independent mechanics, and unknown repairs were performed on the vehicle; however, the failure persisted. The contact took the vehicle to a dealer, where a diagnostic test was performed. The diagnostic test determined that the flex plate was cracked and needed to be replaced. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA Hotline to report the failure. The vehicle was not repaired. The failure mileage was approximately 117,000.

The contact owns a 2020 Ford Fusion. The contact stated that while driving at approximately 40 MPH, there was an abnormal rattling sound coming from the engine compartment. The contact stated that the sound was more evident while the vehicle was idling. The vehicle was taken to an independent mechanic and was diagnosed with a fractured flex plate. The contact was informed that the flex plate needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 63,000.

The contact owns a 2020 Ford Fusion. The contact stated while driving 70 MPH, the vehicle started pulling and veering to the right, while driving on uneven pavement. The power steering assist warning light illuminated while driving over 35 MPH. On another occasion, the steering wheel failed to respond, and the vehicle spun out and the vehicle came to a stop in the right lane. The vehicle was taken to a tire shop where it was diagnosed with rack and pinion failure, and the vehicle was aligned. The vehicle was repaired; however, the failure persisted. The contact then took the vehicle to an independent mechanic who diagnosed the vehicle with a steering assist sensor fault. The brakes were calibrated; however, when the contact depressed the brake pedal, the brakes failed to respond, and the contact stopped depressing on the accelerator pedal to have the vehicle slow down to stop the vehicle. The dealer was not made aware of the failure. The vehicle was not repaired for the most recent failure. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 87,361.

My vehicle was in service with my dealer for several months 3 separate occasions for powertrain issues which werent resolved and now the alignment in my steering wheel is really off. My spouse and I believe the PCM is messed up but have had no progress with our dealership and suspect them of committing consumer fraud and selling us a lemon. The vehicle in question is around 70,000 and started messing up at 60,000.

Began to hear loud rattling noise under hood. Brought to Ford dealer who determined the cause is a failed Flex Plate. Car is operable but was warned this could result in catastrophic failure of the transmission. Vehicle has approximately 62,000 miles, just 2,000 miles out of warranty. Ford Customer Satisfaction Program 22N12 address the issue with an extended warranty for certain model variants (Vehicles Equipped with a 2.0L EcoBoost Engine and 6F35 Transmission). My vehicle has suffered the same failure but has a 1.5L engine so has been excluded.

The steering cable is connected to the transmission hub, and the fitting that connects the two has a gasket that wears away and falls out. This is a recall with vehicles that are made from one of the two plants that assemble fusions, however my vehicle is not covered under the recall even though it is the very same issue as the recall from the other plant. it makes no sense, why is one assembly plant offering a recall for this issue while the other does not? For the same issue of the steering cable coming off the transmission, and not allowing the vehicle to go into gear. I have had to fix this car on the side of the highway before, it will not go into gear on the road. This is not safe at all. You cannot have vehicles just not going into gear while your driving down the highway, or road, street, etc.

Hard shifting when accelerating/decerating, jerking of the car due to transmission issues (80k miles), ABS/Braking issues due to engine components not being in sync, etc

When these problems started it was only 6 months after purchase and I was already having issues with power train malfunctions and it didnt want to switch gears. I purchased this at roughly 47,000 miles and it didnt make it to 70,000 miles before I ultimately decided it was not the safe vehicle that was advertised to my family and I. It was taken to the dealership over 3 times in under a year and for some reason the problem never got resolved. I have been sued for the remaining balance now despite that toward the end of my time owning it the vehicle was reving out with barely any pressure on the gas pedal, having issues braking on its own (anti-collision assist), and occasionally the steering wheel would jerk me in to oncoming traffic. I am just trying to get a recall issued at this point because this car is going to kill someone if it stays on the road.

The contact owns a 2020 Ford Fusion. The contact stated that while making a turn in either left or right direction, the Traction Control warning light had displayed, and the vehicle had reduced speed independently. During failure, the contact lost control of the vehicle and crashed into a mailbox. During the crash, no injuries were reported. No police report was filed and the vehicle was driven home. The cause of the failure was not determined. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 81,000.

COMPONENT: ELECTRICAL SYSTEM, ENGINE I HAVE HAD THIS SENSOR THAT MAKES MY CHECK ENGINE LIGHT STAY ON 3 SEPARATE TIMES! THIS NEEDS TO BE RE CALLED I SEE MULTIPLE COMPLAINTS WITH THE SAME CONCERN

The alternator was producing too many volts, which would short circuit the battery and electrical components in the car. This would cause the car to lose power and not be able to accelerate. My car would randomly lose power on the highway, with no warning, resulting in my car suddenly slowing down. This was dangerous for the cars around me who are going 60+ and then my car quickly drops to 40 or less mph. In addition, to solve the issue I would have to pull off onto a shoulder to shut the car off and back on. This issue started around 3-4 yrs ago and has gotten worse as time passed. The problem was identified and resolved by Firestone when they ran a diagnostic. No check engine light was on in the car to alert me of any issues. I replaced both parts on the car.

Car shifts into 1st gear when traveling at higher speeds (45+mph), causing a significant jerk and almost causing a rear end collision to myself. Car also loses power and jerks significantly hardwhen shifting to reverse and drive from Park. Afraid to travel over 45mph due to the downshifting.

In 2024 on Black Friday while driving home from work my car all of a sudden was starting to lose speed. Even when I'm hitting the gas it would not accelerate and I could push it all the way down to the floor or nothing. And all of a sudden I start to see a whole bunch of monitors go off on my dashboard animal League to the government off and then all of a sudden I started see this underneath my core board pulled over and all sudden those planes coming from my engine and within minutes the whole car was destroyed. Fire department came to drop the fire and everything but the trunk was left essentially. The insurance company has taken to car since and I believed it was sold for parts. I have Thought I had submitted this before but never got somebody you can just in case I messed up. I just feel like a car shouldn't just randomly catch fire

The contact owns a 2020 Ford Fusion. The contact stated that while the vehicle was at the car wash, water entered through the closed sunroof. The vehicle was taken to an independent mechanic, who determined that the sunroof drain needed to be cleaned. The sunroof drain was cleaned, but the failure persisted. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 20V260000 (Visibility); however, the VIN was not included in the recall. The manufacturer was made aware of the failure and instructed the contact to take the vehicle to the dealer to have the sunroof replaced. The failure mileage was approximately 80,000.

The contact owns a 2020 Ford Fusion. The contact stated the vehicle was started and the check engine warning light illuminated. The contact had taken the vehicle to an independent mechanic where it was diagnosed and determined that there was coolant intrusion into cylinder #2, and the engine needed to be replaced. The vehicle was not repaired. The manufacturer was not informed of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 68,000.

The contact owns a 2020 Ford Fusion. The contact stated that while operating the vehicle, there was a ticking and knocking sound coming from the engine compartment. The vehicle was taken to the local dealer. The cause of the issue was not yet determined. The manufacturer was not contacted. The failure mileage was 79,000.

There was a recall on 2020 Ford Fusions in 2022 on flex plate. My car miles at 90,000 and I started to hear the ticking noise. I did my research and I seen that it has the same noise that my car is making now. I called the dealership and the dealership said that I had no active recalls on my car and that the recall was specific to certain cars. Even though my car wasn’t apart of the specific VIN. I had a mechanic check it out and it was the flex plate. I’m still having issues with my flex plate but they want me to come out of pocket , I never had a engine light or anything come on I just started hearing this loud noise and it progressively has gotten worse.

On Saturday, October 5th, 2024, at around 5AM I was sitting in the Starbucks parking lot outside of the Detroit Metro (DTW) airport when this issue began. I had just started my car and could feel it was sluggish and was making a significant amount of noise, which was present in park and neutral, but not so much while in gear, unless I was stopped at a stop sign or stationary. After getting home, and each day after when I started the vehicle to go to work, I could hear that the noise was progressively getting worse. So, I determined that it was not a fluke and took my car into a Ford dealership to have the oil changed and a full inspection done. They explained to me that the water pump had failed and was leaking, very slowly, but externally through the "weep hole". They were going to charge me $1,300 to repair. So, I called a local shop that I know is reputable and they confirmed the water pump leak but determined that the noise I was hearing was not the water pump, but actually a cracked flexplate. The noise originated near the starter, and the shop ran a camera through the inspection hole confirming this. After I found that the flexplate was cracked, I did not continue to drive it, but scheduled a repair to begin on Thursday, October 24th at the reputable shop I mentioned above. To complete the repair, they needed to drop the cradle, remove the transmission and support the engine. This in total cost me $1,729.60. The flexplate has not been inspected by the mfg., police, insurance, etc., as there was no need. I did not have an extended warranty and though my car is only 4 years old, it was beyond the warranty in miles. No lights appeared on the dash, and there were no error codes present. The flexplate cracking could have resulted in catastrophic failure of the engine or transmission, and I could have very well lost control of my vehicle. If I was driving on the highway during a failure, my safety as well as others would have been put in serious danger.

The contact owns a 2020 Ford Fusion. The contact stated while driving at an undisclosed speed, the front passenger's side low beam headlight failed to illuminate as needed. Upon inspecting the vehicle, the contact noticed that the front passenger's side low beam headlight assembly wiring harness was burnt, and there was light smoke coming from the wiring harness. The vehicle was taken to the local dealer, where it was diagnosed that the low beam headlight assembly needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was 53,000.

The contact owns a 2020 Ford Fusion. The contact stated while driving 30 MPH, the vehicle hesitated and stalled while depressing the accelerator pedal. The check engine warning light was illuminated. The dealer was contacted and notified of the failure. The vehicle was diagnosed with an internal engine failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 65,000.

Tire Pressure Monitor System Warning Action Now Issue Since 09-22-2024 The tire pressure monitoring system has detected one or more tires are significantly under-inflated. Suggested Actions: Check the tire pressure to ensure the tires are properly inflated. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge. See Inflating Your Tires in the Wheels and Tires chapter of your Owner's Guide. Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle rollover and personal injury.

The contact owns a 2020 Ford Fusion. The contact stated while attempting to start the vehicle, smoke and an abnormal odor was coming from the rear of the vehicle. The check engine warning light was illuminated. The vehicle was driven to the dealer. The dealer determined that the failure was caused by a purge control valve failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 40,000.

THE COMPONENT THAT HAS FAILED IS THE FLEXPLATE, TRANSMISSION FLUID PUMP, AND TORQUE CONVERTER. IT WAS EVALUATED BY FORD AND CONFIRMED THAT IT IS THE SAME ISSUE AS A PREVIOUS CSP THAT FORD ISSUED IN 2022/23, BUT I WAS NEVER NOTIFIED OF THE ISSUE. NO LIGHTS OR WARNINGS PRIOR TO THE ISSUE. IT BECAME NOTICEABLE ON OR AROUND 9/20/24.

On [XXX] I backed my 2020 Ford Fusion out of my driveway. I stopped and tried to shift from reverse to drive and the transmission locked up in Park, the engine died and the parking brake was engaged. I was sitting across the street with no way to move the car. I had the car towed to a Ford dealer and they replaced the transmission cable bushing and cover. These parts are the same as those used in Fords recall 22S43. Ford continued to use inferior parts on cars built after the dates mentioned in the recall. This is a safety issue as it could happen at any time. Thanks [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

My 2020 Ford Fusion developed a oder coming from the a/c heat system. In a few days it got bad enough to determine something died in the vehicle! I went to the cabin air filter to replace it but as I started to pull it out there was debris stopping it! So I removed the front cowling to expose the fresh air inlet and found it was full is mice droppings and nuts. I then found a dead mouse that got its head stuck in the recirculating door that is for max A/C! After a while of vacuuming out the air filter top and removing the dead mouse. I was able to remove the cabin air filter and then removed the blower motor below it to clean the debris from that. The debris feel when I went to remove the air filter as the opening scrapes the top of the filter as you remove it! I wiped every thing down with bleach wipes and vacuumed as much as i could then blew out the system with compressed air and reassembled the vehicle. When I was done I looked up "how mice can get in there" and found out I'm not the only one this has happened to. Since the air filter does not filter out viruses and bacteria this is a serious health problem. People can get Hantavirus (67% mortality rate) from mice, droppings, as well as other bacterial infections, and viruses! It can kill anyone in the car riding in by breathing the virus coming from the heating or a/c system. The outside air inlet should have a tightly conforming mesh covering to prevent mice and other rodents from getting into the A/C system in all vehicles. Or the recirculating door can be programed to close when the vehicle is shut off! Note the vehicle still smells a bit and I'm going to have it detailed and use a disinfectant sprayer to clean out the entire A/C heating system that I ordered.

Flex plate is cracked , confirmed by bore scope dealership is quoting 14 business days to diagnose. It is known issue with this make, model, and year and CSP was issued for dealerships to fix but only select VIN numbers. This car is at 91000 miles and meets all criteria for the CSP 22N12. The car makes an ungodly rattling sound and if it fails could be very dangerous

My flex plate cracked on my 2020 Ford Fusion. Ford has a customer satisfaction program stating that they have a one time repair for cracked flex plates, torque converter, and transmission pump and are refusing to honor it. Once the dealership confirmed my flex plate was cracked they were notified that the repairs were not going to be approved I was giving a quote for $4700 to pay out of pocket. I did not have the money and went to pick my car up until I figured out a solution. While in the process of waiting to figure out my next step of action I was informed by one of the service writers that they were going to approve my repairs by this time my vehicle had completely stopped on me while on the highway with my child in the car. Once it was towed to the dealership my car sat for 2 weeks untouched because of other repairs and I was later informed that Ford is wanting to overturn their decision and not repair my car.

The contact's husband owns a 2020 Ford Fusion. The contact stated while driving at various speeds, there was an abnormal rumbling sound coming from the engine. There was no warning light illuminated. The vehicle was taken to a dealer where a diagnostic test was performed. The mechanic discovered a failure with the flex plate. The contact was initially informed that the vehicle was covered under warranty; however, the contact was later informed that the engine repair was not covered under warranty. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The vehicle remained with the dealer unrepaired. The failure mileage was approximately 70,000.

The contact owns a 2020 Ford Fusion. The contact stated that while driving at various speeds, there was a rattling sound coming from the engine compartment. The contact stated that the sound was also noticed while idling or with the air condition activated. The check engine warning light was illuminated. The vehicle was taken to a local dealer where it was diagnosed and determined that the flex plate needed to be replaced. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 84,994.

The engine is “eating” the coolant causing the vehicle to overheat and break down.

The entire media display gets stuck off or will freeze up, when I place the vehicle in reverse the rear camera comes on but parking assist, the rear sensors and cross traffic sensors won't work. Once I place the car in drive the display will either stay all blue or shut completely off. I cannot adjust the climate control, use GPS, or use the media. I have to shut the car off and then after about 10 minutes there is a bunch of clicking noise under the dash and after it stops clicking I can restart the car, the display will sometimes begin to work and if it dossent then I have to shut off the car again and go through the motions again. It has started to be more and more frequently, at first it was maybe once a week and now it is happening at every start.

Cracked flexplate

The contact owns a 2020 Ford Fusion. The contact stated that while starting the vehicle, there was a rattling noise coming from the front end near the driver’s side close to the transmission. The vehicle would start moments after the failure had occurred. The rattling was more pronounced while the A/C system was running. The contact stated that while depressing the accelerator pedal, the rattling sound was noticeable. Additionally, while driving at various speeds, the transmission felt as though it was slipping while changing gear. The contact stated that while inspecting the engine, underneath the hood was hotter than normal. The check engine warning light was illuminated. The vehicle had been taken to the dealer where it was diagnosed that the transmission flex plate had failed. The failure was linked to NHTSA Campaign Number: 10218899 (Power Train). The vehicle had not been repaired. The manufacturer was made aware of the failure, and it was confirmed that the VIN was not under recall. The contact was referred to the NHTSA Hotline to file a complaint. The failure mileage was 117,000.

The contact owns a 2020 Ford Fusion. The contact stated that the hood latch was no longer functioning and the hood was not able to be raised. The contact stated that he had taken the vehicle to an independent mechanic who was unable to repair the failure. The manufacturer was informed of the failure and referred to the NHTSA Hotline. The failure mileage was approximately 103,000.

Intrusion into cylinder 2.

Rattling and lost of power

The contact owns a 2020 Ford Fusion. The contact stated while starting the vehicle, the vehicle made an abnormal rattling sound. The contact stated that the failure had been recurring. The vehicle was taken to an independent mechanic, where it was diagnosed that there was a rattling sound coming from the transmission bell housing area, and the flex plate was cracked. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the failure was related to Ford Campaign Number: 22N12. The manufacturer assisted the contact in scheduling an appointment with the dealer for diagnostic testing. The manufacturer also referred the contact to the NHTSA Hotline for assistance. The vehicle was not repaired. The failure mileage was approximately 95,755.

The contact owns a 2020 Ford Fusion. The contact stated while operating the vehicle, there was a loud knocking sound coming from the engine compartment and the battery had failed. The vehicle was taken to the local dealer who diagnosed that the transmission flex plate had failed. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 102,864.