2025 GMC Yukon Engine Problems

My engine completely failed on March 19, 2026 and it is currently at Sterling GMC in Bryan Texas waiting for a backorder engine as it needs to be completely replaced

Engine failure while driving at 60mph that started with a loud knocking sound to eventual engine failure where it wouldnt turn over. Vehicle has 9600 miles and has had issues since day one of leaving lot requiring fuel injector, intake manifold gasket, lifter and rod with last fix being new coil and spark plug that supposedly fixed issue. The most recent engine failure put my family and kids in danager given 100 degree weather in middle of desert on a small highway with very limited cell service. Vehicle provided no warning lights. Vehicle was towed to dealership and I have not received an update. Vehicle has not been inspected by polive or insurance or others.

The contact owns a 2025 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly went into LIMP Mode with a limited speed availability message displayed. The vehicle was restarted; however, the failure recurred. The vehicle was taken to the dealer, where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 8,837

Vehicle went into limp mode while driving on the highway. Onstar said it was the transmission. Checked the oil and smoke was billowing out of the dip stick and there was no oil. None of the sensors indicated that there was low oil. After sitting and waiting for a tow truck rechecked the oil with the dipstick and there was oil in it. Now requires a new engine.

Engine started knocking and developed slow acceleration out of the blue. In addition car has locked up on freeway despite not having any cars around me. Its been in the shop for 3 days and still no diagnosis.

Warning about reduced acceleration and need for immediate servicing. Dealership reports notice about this issue by using diagnostic codes. Needs engine and turbo charger replaced. Vehicle has only 6500 miles on it.

Engine Failure confirmed by dealership. Engine being replaced. Knocking sound and went in to “limp mode” and check engine light. Dealer stated it had issue with crank shaft causing metal in the oil. 5,117 miles at time of failure. 3.0 L Duramax diesel

My 2025 GMC Yukon AT4 Ultimate experienced reduced acceleration, and I immediately took it to the dealer. The dealer concluded it was a thrust bearing failure, and GM has authorized a complete engine replacement. I wanted to report this issue, as I believe it represents a potential safety concern. I would like to clarify whether GM has identified the root cause of this problem and redesigned the replacement engine to prevent recurrence. Additionally, I want to be able to track the replacement engine through its serial number for documentation purposes. I am submitting this report to formally document my concern. While GM has acknowledged the thrust bearing issue through a memo #25-NA-307, they have not confirmed whether the redesigned replacement engine will prevent this failure from happening again. Please advise. Sincerely, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

On November 5, 2025, this 2025 diesel GMC Yukon Denali brand new vehicle went into "limp mode" 75 days after purchase with 3,957 miles on the odometer. Vehicle began to decelerate on a busy road. Warning lights went on to indicate that accelerating was no longer possible. Other fast-moving vehicles on the road came very near to the Yukon and quickly passed it/weaved around it, jeopardizing the lives of this Yukon's driver and occupants. At times, the Yukon diesel vehicle would only reach 15 MPH. Vehicle eventually driven to nearest GM dealership. The GM dealership service center reported a P06D code and reported that the engine experienced catastrophic engine failure. A new diesel engine has been ordered but is not yet available to the dealership for installation. (The dealership also reports that two other new GM diesel SUVs are waiting on new engines due to catastrophic engine failure.)

On October 21, 2025, with only 4,197 miles on my Yukon, the vehicle suddenly died while in drive in a parking lot. The vehicle would not restart or shift into neutral. I contacted OnStar, who arranged for the vehicle to be towed to the nearest GMC dealership. Since that date, the vehicle has remained at the dealership and has been diagnosed as needing a complete engine replacement due to metal shavings found in the engine. There were no warning lights, messages, or performance issues prior to the failure. This incident was both unsafe and alarming, as the vehicle shut down unexpectedly without any warning while I was driving. I would like to understand how such a major failure could occur on a brand-new vehicle with so few miles.

The 3.0L diesel motor failed around 5700 miles. The thrust bearing failed and the engine and the turbo needed to be replaced.

The 6.2 engine in our 2025 Yukon Denali with 3,200 miles just locked up. It needs to be replaced. They said they fixed the problem and it was only affecting 2021 to 2024, but it is carrying over into 2025. They should just buy this vehicle back.

suddenly went into limp mode on the highway, engine had to be replaced due to bearing failure sending metal through the engine

I just bought this 2025 GMC Yukon a little over a month ago, and the 6.2 engine has seized up. This vehicle started making grinding noises and shut down going 60 miles an hour. I traded in my previous Yukon and the dealer has sold it, so now I have nothing to drive. These engines are dangerous, and GM knows this and they don't seem to be doing anything about it

Brand new engine blew up while driving. It had 2,000 miles on it. It has been replaced but am worried it will happen again

While driving on the highway, my SUV lost speed and went into what I believe was limp mode and the check engine light came on. I was unable to accelerate quickly which was very dangerous on the highway as I was only able to very slowly go about 45 MPH on a 65 MPH highway. After the dealer inspected it, I was told I needed a new engine, oil cooler, and turbo. They said it had metal in the oil. My SUV only had 2138 miles at the time of incident.

At approximately 500 miles, the vehicle started to shutter and misfire at highway speeds (60-70 mph). The check-engine -light began to flash at the same time. We have a video and this happened 3 times before taking it to the dealer. This is a safety concern because it began to lose power on the highway. The issue was confirmed by the dealer and found to be damaged connecting rod bearings.Gm engineers are aware of the vehicle and would not approve the ordering of a new engine by the dealer until the engine was completely torn down to the point of failure.

The contact owns a 2025 GMC Yukon. The contact stated while driving at an undisclosed speed, the vehicle was vibrating abnormally, and the engine seized. No warning light was illuminated. The vehicle was restarted and taken to the dealer to be diagnosed. The contact was informed that there were metal shavings in the oil pan, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was being repaired. The manufacturer was made aware of the failure and a case was filed. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 3,000.

PLEASE SEE ATTACHMENT:

I had Three 2024 6.2L engines in my GMC Sierra BLOW UP.....