2016 Ram 3500 Steering Problems

The contact owns a 2016 Ram 3500. The contact stated that upon inspection, the tires showed excessive wear. The contact stated that the vehicle had been previously repaired under NHTSA Campaign Number: 19V021000 (STEERING); however, the recall repair failed to fix the vehicle. The contact stated that the failure persisted after the recall repair. The manufacturer was not notified of the failure. The failure mileage was approximately 78,000.

The contact owns a 2016 Ram 3500. The contact stated that while driving approximately 70 MPH, the steering rack fractured, and the contact was no longer able to maneuver the vehicle. The contact strapped the steering wheel into place to maneuver the vehicle. No warning lights were illuminated. The vehicle was taken to a dealer where it was diagnosed and determined that the steering rack needed to be replaced; however, the cause of the failure was not known. The vehicle was not repaired. Another dealer was contacted and confirmed that the steering rack needed to be replaced and assisted the contact with finding the parts to repair the vehicle. The vehicle was repaired; however, the failure persisted. The manufacturer was not notified of the failure. The failure mileage was approximately 275,000.

death wobble incident in my Ram 3500. Incident occurred while pulling a 35' foot Living Quarters horse trailer weighing over 26,000 pounds on the interstate. Have major vibration, shaking, and thumping sound in truck which gets worse the faster I accelerate. Chrysler needs to issue a recall on this issue get it resolved. See that this has already been report to NHTSA. February 24, 2024 NHTSA ID NUMBER: 11573822 Components: STEERING, SUSPENSION

The contact owns 2016 Ram 3500. The contact became aware that the front passenger's side tires had been wearing out prematurely. The vehicle was taken to a tire shop, and the contact was informed that an alignment could not be performed on the vehicle. The manufacturer was notified of the failure and informed the contact that he would be referred to a specialist for assistance. The specialist called the contact and referred him to a dealer for assistance. The vehicle was taken to the dealer, who informed the contact they could not perform an alignment because the steering linkage jam nut was previously welded to the adjuster sleeve under NHTSA Campaign Number: 19V021000 (Steering). The dealer determined that the drag link assembly needed to be replaced to perform the alignment of the vehicle. The dealer was awaiting manufacturer’s authorization on the drag link assembly replacement. The vehicle was not repaired. The failure mileage was approximately 122,000.

The contact owns a 2016 Ram 3500. The contact stated that the vehicle was inspected and informed of NHTSA Campaign Numbers: 19V021000 (Steering) and 18E096000 (Steering). The contact stated that while driving at highway speeds, the vehicle was drifting to the left and the right. The contact had to drive at speeds lower than 15 MPH to prevent the drifting from occurring. The contact took the vehicle to the dealer and was informed that the recall repairs were previously completed and was a one-time free repair. The vehicle had not been repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 149,000.

Four death wobble incidents in the last 18 months. Unknown part failure, Replaced front track bar, right front wheel bearing pack, front suspension stabilize shock.

The contact owns a 2016 Ram 3500. The contact stated after purchasing the vehicle, the local dealer informed him about NHTSA Campaign Number: 19V021000 (Steering) however, the part to do the recall repair was not yet available. The dealer stated informed the contact that the nut would be welded and the vehicle would need an alignment. The contact stated that the steering wheel was not completely straight. The contact took the vehicle to an independent mechanic and who was unable to align the vehicle due to an issue with the drag link. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 68,190.

Steering is failing. Steers like a boat. Looses control in turns. Over adjustment and correction must be done to maintain course. Same issue occurred in a Dodge Challenger.

WHEN DRIVING DOWN ROAD CONSTANTLY MAKE ADJUSTMENTS TO RIGHT AND OR STEERING WHEEL BEING HELD TO OR AROUND 1 OR 2 O'CLOCK POSITION JUST TO GO STRAIGHT. WHEN STEERING TO LEFT STEERING WHEEL IS TIGHTER THEN WHEN STEERING TO RIGHT. STEERING BOX NEEDS REPLACED AND OR REBUILT. TRUCK ONLY HAS ALITTLE OVER 60000 MILES ON IT. CONSTANTLY CHASING STEERING WHEN DRIVING DOWN ROAD. CITY STREETS AND LEFT LANE OF HIGHWAYS ITS EXTREMELY NOTICABLE. HAD TRUCK ALIGNED AND ALIGNMENT SHOP SAYS ALIGNMENT IS DEAD ON. AFTER READING MULTIPLE AND MULTIPLE FORUMS AND OTHER INFORMATION ONLINE, THIS IS A EXTREMELY COMMON PROBLEM WITH THESE TRUCKS YET NO RECALL TO FIX. RED HEAD IS A COMPANY THAT REBUILDS/UPGRADES THESE STEERING BOXES, BUT THE COST WITH SHIPPING IS AROUND $800. CHRYSLER SEEMS TO DENY THERE IS A PROBLEM WITH THE STOCK STEERING BOXES ON THE RAM 2500/3500 TRUCKS, THERE ARE THOUSANDS AND THOUSANDS OF PEOPLE THAT ARE HAVING THE SAME ISSUE YET NO RECALL TO FIX THE PROBLEM.

I APPLAUD YOUR WORK IN HOLDING AUTOMAKERS ACCOUNTABLE AND RESPONSIBLE FOR FIXING VEHICLE SAFETY ISSUES. HOWEVER, MY VEHICLE WAS RECALLED FOR V06/NHTSA 19V-021 (STEERING SYSTEM RECALL). RATHER THAT PROVIDING NEW PARTS FOR THE DEFECTIVE PARTS, RAM STATES THAT NHTSA HAS APPROVED WELDING THE STEERING JAM NUTS TO THE ADJUSTER. THE DEALER SUBMITTED A STAR CASE (#101582875) TO HAVE REPAIR PARTS PROVIDED WHICH WAS DENIED, BASED ON NHTSA APPROVAL OF WELDING. ALSO, CALLED RAM CARE (CASE # 68052515) THEY REFUSED TO PROVIDE REPAIR PARTS AND DIRECTED ME TO CONTACT THEIR FCA HQS VIA STANDARD MAIL. IT IS APPALLING TO ME THAT WE HAVE HEAVY DUTY TRUCKS ON THE ROAD THAT COST OVER $60K AND RATHER THAT REQUIRING RAM TO REPLACE DEFECTIVE PARTS, WE ALLOW THEM TO WELD PARTS. MOST OF THESE HEAVY DUTY TRUCKS ARE USED TO HAUL HEAVY TRAILERS. WELDS IF NOT DONE PROPERLY WEAKEN METAL AND CAN BREAK UNDER STRESS. ADDITIONALLY, THIS FIX (WELDING) RENDERS STEERING SYSTEM ADJUSTMENTS INOPERABLE WITHOUT GRINDING THE WELD ADJUSTING THE STEERING AND RE-WELDING THE PART ALL OF WHICH DAMAGES AND STRESSES THE CRITICAL EXISTING STEERING PARTS. REQUEST THAT NHTSA REQUIRE RAM TO REPLACE THE DEFECTIVE STEERING PARTS AND NOT ALLOW A JAM NUT TO THE ADJUSTER WELD AS A PERMANENT FIX TO THE STEERING SAFETY RECALL. THANKS

GENTLEMEN, THIS COMPLAINT IS IN REGARDS TO THE CURRENT V06 RECALL THAT AFFECTS RAM HEAVY DUTY TRUCKS. THE CURRENT FIX OF WELDING COMPONENTS OF THE STEERING SYSTEM BY UNCERTIFIED PEOPLE IN AN UNCONTROLLED ENVIRONMENT IS SOMEWHAT CONCERNING. I HAVE NOT HAD THIS DONE TO MY TRUCK BASED ON THE HIGH NUMBER OF OWNERS DESCRIBING SOME OF THEIR RESULTS DONE BY THE DEALER. I WILL INCLUDE A COUPLE OF EXAMPLE PHOTOS. NOT ONLY IS THE WELDING OF COMPONENTS VERY INCONSISTENT, IT CHANGES THE MOLECULAR STRUCTURE OF THE COMPONENTS INVOLVED. IT ALSO RENDERS THE ABILITY TO CORRECTLY DO A FRONT END ALIGNMENT IMPOSSIBLE WITHOUT MAJOR MODIFICATIONS HAS A NEW AND IMPROVED DRAG LINK (#CSZHV061AA) THAT IS AVAILABLE BUT IS VERY RELUCTANT IN SWAPPING THESE OUT. I WOULD GREATLY APPRECIATE AN INVESTIGATION ON THE RESULTS OF THIS CURRENT FIX AND LONG TERM ISSUES TO OWNERS. THE TRUCKS ARE CAPABLE AND DESIGNED TO TOW MASSIVE AMOUNTS OF WEIGHT AND DO SO ON A DAILY BASIS. ALL THE MORE REASON TO FIX IT RIGHT BEFORE MORE ACCIDENTS HAPPEN. THANKS! CONCERNED!! [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).? *PM

TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT HAD THE VEHICLE SERVICED FOR NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING). DUE TO THE RECALL REMEDY, THE CONTACT WAS NO LONGER ABLE TO OPERATE THE VEHICLE PER FEDERAL MOTOR CARRIER GUIDELINES. AS A RESULT, THE CONTACT HAD THE RECALL REPAIR REVERSED IN ORDER TO UTILIZE THE VEHICLE. THE MANUFACTURER WAS NOTIFIED AND STATED THAT THEY WOULD REPAIR THE VEHICLE WITH A NEW AND DIFFERENT REMEDY AT THE CONTACT'S EXPENSE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. *DT*JB *TR 'PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).'*JB

FCA AND THE DEALER REFUSES TO VERIFY THE SAFETY OF MY TRUCK. I BROUGHT MY TRUCK TO THE DEALER FOR RECALL NHTSA 19V-021 (DRAG LINK). I TOLD THE DEALER I WANTED THEM TO INSPECT THE DRAG LINK NUTS TO INSURE THEY WEREN'T COMING OFF. I ALSO SAID I DIDN'T WANT THE NUTS WELDED TO THE DRAG LINK. WELDING THE NUTS WOULD PREVENT ADJUSTMENT WHEN ALIGNING THE TRUCK IN THE FUTURE. THE DEALER SAID THEY WOULD CUT OFF THE WELDS WHEN DOING THE ALIGNMENT. UNFORTUNATELY THIS WOULD FORCE ME TO RETURN TO THE DEALER, WHICH IS ALMOST AN HOUR AWAY, AND WOULD PREVENT ME FROM GETTING AN ALIGNMENT AT ANY NORMAL SHOP. THIS IS FORCING ME TO PAY MORE MONEY FOR ANY FUTURE ALIGNMENT. THE DEALER REFUSED TO INSPECT THE TRUCK. HE SAID THAT THE ONLY WAY THEY WOULD LOOK AT THE DRAG LINK WAS IF THEY PERFORMED THE ENTIRE RECALL, INCLUDING WELDING THE NUTS. I ASKED IF I LET THEM WELD THE NUTS WOULD THEY REPLACE THE DRAG LINK AT A LATER TIME WHEN THE NEW PART BECAME AVAILABLE, THEY SAID NO. I AM NOW DRIVING A TRUCK THAT I DO NOT KNOW THE SAFETY OF BECAUSE OF THE DEFECTIVE DRAG LINK. I CALLED FCA AND OPENED A CASE (NUMBER AVAILABLE). FCA TOLD ME THIS WAS UP TO THE DEALER. WHY DO I HAVE TO ACCEPT A NON-STANDARD SOLUTION TO A PROBLEM THAT WILL NOT GET ME A NEW, UPGRADED PART, AND WILL COST ME MORE MONEY IN THE FUTURE THROUGH NO FAULT OF MY OWN?

TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 18E096000 (STEERING). THE CONTACT TOOK THE VEHICLE TO HUMES CHRYSLER JEEP DODGE & RAM (1010 ROUTE 19 NORTH, WATERFORD, PA 16441, (888) 571-5737) WHERE THE RECALL REPAIR WAS PERFORMED. THE VEHICLE WAS RETURNED TO THE CONTACT. A FEW MONTHS LATER, THE VEHICLE NEEDED THE OUTER TIE ROD REPLACED AND A FRONT END ALIGNMENT. THE CONTACT TOOK THE VEHICLE TO AN INDEPENDENT MECHANIC AND WAS INFORMED THAT, DUE TO A WELDING THAT HAD BEEN PERFORMED ON THE VEHICLE FROM THE RECALL REPAIR, THE VEHICLE COULD NOT BE REPAIRED. THE MANUFACTURER WAS NOTIFIED AND STATED THAT THE WELDING WAS AN APPROVED REPAIR BY NHTSA AND HE WOULD NEED TO CONTACT NHTSA FOR MORE INFORMATION. THE VIN WAS UNKNOWN. THE CONTACT HAD NOT EXPERIENCED A FAILURE. *BF *TP

JAM NUTS ON DRAG LINK ADJUSTER KEEP LOOSENING. RAM HAS ISSUED A JUNK FIX BY WELDING THE NUTS TO ADJUSTER SLEEVE. WELDING ON MY TRUCK IS NOT ACCEPTABLE. I WANT A REPLACEMENT PART, NOT A WELD FIX. SAFETY RECALL V06 / NHTSA 19V-021 DRAG LINK

I RECEIVED A RECALL NOTICE #V06/NHTSA19V-021 IN THE MAIL, SO I WENT OUT TO INSPECT THE DRAG LINK ON MY 2016 RAM 3500 AND NOTICED THAT THE LOWER JAM NUT HAD BACKED OFF THE THREADS ABOUT A 1/4" IN. CONTACTED THE DEALER TO SEE WHEN THEY WOULD BE ABLE TO FIX THIS ISSUE AND WAS TOLD TO CALL BACK IN A FEW WEEKS. AND I SPOKE TO THE SERVICE ADVISER TO SEE WHAT THE FIX WAS GOING TO BE AND WAS TOLD THAT THEY WOULD TIGHTEN THE JAM NUT AND WELD NUT TO THE SLEEVE. I HAVE BEEN A WELDER FOR OVER 30 YEARS AT THE PSNS IN BREMERTON, WA.. IF YOU DO NOT KNOW THE MATERIAL TYPE AND WELD FILLER MATERIAL TYPE IT COULD CAUSE A FAILURE OF THE WELD AND THE MATERIAL THAT IT IS WELDED TO. ALSO, ANYTIME YOU WELD SOMETHING THE HEAT AFFECTED ZONE IS A WEAK SPOT. I DON'T THINK THIS CORRECT FIX DUE TO IT BEING A STEERING COMPONENT. *DT*JB

TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED NOTIFICATION FOR NHTSA CAMPAIGN NUMBERS: 17V562000 (ENGINE AND ENGINE COOLING), 17V821000 (POWER TRAIN), 18V486000 (STRUCTURE, LATCHES, LOCKS, LINKAGES) AND 19V021000 (STEERING). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIRS. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND CONFIRMED PARTS WERE NOT AVAILABLE. THE MANUFACTURER WAS NOT ABLE TO CONFIRM WHEN THE PARTS WERE TO BECOME AVAILABLE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

I WAS DRIVING ON THE FREEWAY WITH MY TRAILER LOADED WHEN THE STEERING WHEEL STOPPED CONTROLLING THE DIRECTION OF THE VEHICLE. IT CAUSED ME TO LOSE CONTROL OF THE VEHICLE AND COLLIDE INTO ANOTHER VEHICLE AND HITTING THE FREEWAY MEDIAN WALL. UNKNOWN AS TO THE COMPONENT, I AM STILL WAITING FOR A REPORT.*DT PHOTOS ATTACHED *JB

TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING) AND STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. WOLFCHASE CHRYSLER DODGE JEEP RAM (8170 US-64, BARTLETT, TN 38133, (901) 373-3030) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING) HOWEVER THE MANUFACTURER FAILED TO PROVIDE A PERMANENT REMEDY AND HAD ONLY LIMITED THE REMEDY TO AN INTERIM REPAIR. THE DEALER TRONCALLI CHRYSLER-JEEP-DODGE-RAM (818 ATLANTA HWY, CUMMING, GA 30040, (678) 244-4100) WAS CONTACTED TO SCHEDULE AN APPOINTMENT. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. *BF *AS