2019 Ford Fusion Complaint Log

The 6F35 transmission in BOTH of our Ford vehicles that we drive daily for work and school. The Ford Fusion is currently in the shop, but the Ford Escape is available for inspection. My safety was put at risk as my Fusion suddenly, without warning, stopped accelerating in the middle of a 2 lane highway, very unsafe. My daughter's Escape is putting her safety at risk because she has the same 6F35 transmission, the car is still "drivable" at the moment but not safely drivable, with the rough shifting between 2nd-3rd gear, the slow acceleration and sometimes won't go into gear, her safety is at risk. Like MANY other Ford owners with this transmission, the car will end up breaking down and needing $5000 in repairs. Yes the issue has been reproduced by the service center. No, Ford has not reached out to me, I have left 7 messages without any return calls, I have sent multiple emails that were returned to sender. There were no warning lights, messages or problems on the Fusion prior to this happening. I own two Ford cars that are both undrivable, I cannot get to work, my daughter cannot get to work/school. Ford is VERY aware of this transmission issue but will not issue a recall. Also at times when I put my Fusion into drive, from reverse, the backup camera would stay on for a few minutes which makes driving very hard/confusing and very unsafe. Ford needs to take accountability and issue a recall for vehicles with this defective transmission instead of ignoring the issues and telling buyers their vehicles are reliable.

The contact owns a 2019 Ford Fusion. The contact stated that the vehicle was shaking abnormally at start-up. The vehicle was taken to the dealer however, a cause for the issue was not found. The failure persisted, and the check engine warning light illuminated. The contact's husband replaced the spark plugs and ignition coils; however, several days later, the failure reoccurred, and the spark plugs, and ignition coils were replaced an additional three separate times due to the persistent failure. The vehicle was then taken to an independent mechanic where a diagnostic test indicated that there was coolant intrusion into cylinder #3. The manufacturer was notified of the failure and informed the contact that there were no recalls on the vehicle. The contact was then referred to the NHTSA Hotline to report the failure. The vehicle was not repaired. The failure mileage was approximately 94,000.

I am reporting a serious safety defect involving the transmission system of my Ford Fusion, specifically related to the valve body and torque converter. The malfunction of these components causes sudden, unpredictable surges or lunges in acceleration, even when the vehicle is being driven at steady speeds or when lightly applying the accelerator. The issue appears to stem from improper pressure regulation or fluid flow within the transmission valve body, which causes erratic shifting and delayed engagement. When this malfunction occurs, the torque converter can fail to properly manage torque transfer, resulting in sudden and forceful forward motion of the vehicle. While driving on a highway at approximately 65 mph, my vehicle suddenly lurched forward aggressively, as if it had downshifted or received a surge of power without any change in throttle input. This caused the car to rapidly accelerate momentarily, nearly causing me to lose control. The unexpected forward thrust startled me and forced me to take immediate corrective action to maintain my lane and prevent a collision with a nearby vehicle. In another instance, while slowing down to a stop, the car lunged forward again instead of decelerating smoothly, nearly causing me to roll into an intersection. This created a dangerous situation for myself, my passengers, and surrounding traffic. This defect creates a significant risk of collision due to the vehicle’s unpredictable acceleration behavior. The driver cannot reliably control speed or anticipate when the car may suddenly surge forward. The issue compromises both vehicle stability and driver reaction time, particularly at higher speeds or in traffic. If this problem were to occur in a congested area, at a stoplight, or near pedestrians, it could result in a serious crash, injury, or fatality. The failure of the valve body and torque converter in the Ford Fusion represents a critical mechanical defect that directly impacts safe operation of the vehicle.

coolant intrusion in engine with less than 7 years of life and under 84k miles. wont replace engine with the program because it didnt get the pcm update beforehand. Never got a letter for it and my vin doesnt say im apart of the program even though my car was build in the time frame and plant that they had this coolant intrusion issue.

Coolant intrusion that Ford knows happens with these cars even with maintenance now they want me to pay 10k to get a new Engine with an updated part.

Occasionally, the vehicle will drive in reverse when started and the shifter knob is turned to Drive (forward). This has occurred at least 5 times and the dealership has not been able to replicate the issue. So in their minds, it is not an issue. On one of those instances we noted that that shifter did not have any mode highlighted even though it was put into Drive. There were no warning lamps illuminated, no system messages. The car simply started to reverse when taking the foot off of the brake. The car had to be turned off and restarted multiple times to get it to go forward. This can be dangerous as one could inadvertently strike an object or person that is behind the vehicle.

The car would periodically have white smoke coming out the exhaust I assumed it was bad gas and then all of a sudden it just had a ton of white smoke ended up being the the head gasket to the small block was bad and defective and Ford knew about it and did nothing about it. There was a safety performance alert, which I did not receive.The car is only six years old and I just paid it off.

Ford 2.0L EcoBoost engine. 2017-2019 Fusion. Also, in 2 other Ford and Lincoln models. I bought 2019 Fusion used and car has just under 69000 miles. Due to a known engine defect there can be coolant intrusion into a cylinder. In my case #2 cylinder. See TSB # 22-2229 from Ford. Check engine light came on. took to dealer and replaced 1 ign coil and 4 spark plugs. Thought issue resolved until check engine light came back on. Returned to dealer and advise that engine needed replacement. If continued to operate engine could lock-up while driving thus creating a safety for myself and others on the highway. Ford knows of this defect caused by their design of the block.

The contact owns a 2019 Ford Fusion. The contact stated while driving at an undisclosed speed, the vehicle inadvertently lost motive power. The contact was able to pull over to the shoulder of the roadway, where the vehicle was able to be restarted. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, who determined there was coolant intrusion into cylinder #3, causing damage to the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 82,000.

When I put my car in reverse, the backup camera FREEZES and stays on when driving down the road. Sometimes the backup camera turns blue and stays blue when driving down the road. This increases a chance of a crash risk. My 2019 Ford Fusion is not on the recall list and should be. Mountain View Ford in Chattanooga, TN has confirmed my backup camera freezes and turns blue. This backup camera issue began approximately April 2025.

The contact owns a 2019 Ford Fusion. The contact stated that while driving at an undisclosed speed, there was an engine misfire, with the check engine warning light illuminated. The vehicle was able to restart. The vehicle was taken to the dealer where it was diagnosed with coolant intrusion into the engine, which caused engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The approximate failure mileage was 108,831.

The contact owns a 2019 Ford Fusion. The contact stated that while starting the vehicle, there was a loud clanking noise coming from the engine compartment, with the check engine and transmission warning lights illuminated. The vehicle was able to restart. The vehicle was towed to the dealer, where it was diagnosed and determined that the flex plate had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 126,000.

The failure occurred in the engine block or head gasket of the 2.0L EcoBoost engine, leading to coolant intrusion into the cylinders. Yes, the affected engine components were inspected by local dealer and confirmed long block issue. The safety of the driver and others was put at risk due to the potential for: Sudden engine misfire or stalling, which could lead to a loss of power while driving. White smoke from the exhaust reducing visibility for other drivers. Engine overheating, which could cause a breakdown in traffic or on highways. Yes, the problem has been reproduced and confirmed by a Ford dealer and/or independent service center through diagnostic tests, which identified coolant intrusion into the cylinders. The vehicle has been inspected by the manufacturer’s authorized dealer during diagnostic testing to confirm the issue. It has not been inspected by police or insurance representatives. Yes, warning lamps and other symptoms appeared prior to the failure, including: MIL (Check Engine Light) with DTCs such as P0300-P0304 White exhaust smoke, indicating coolant burning in the engine. Engine running rough, especially during cold starts. Low coolant level, requiring frequent refills, with no visible external leaks. These symptoms first appeared [insert time frame or mileage if known].

Coolant is intruding into the engine, with no sign of a leak. There was a TSB 22-2229 issued that my car falls under, but ford claims they are not at fault to pay for it. This was a manufacturing error, and was at no fault of my own. My car has less than 60k miles on it. A check engine light came on for cylinder 3 misfire. There was no warning signs that an engine failure was occurring. The car is not driveable as it could overheat at any moment.

The contact owns a 2019 Ford Fusion. The contact stated that while driving approximately 30-35 MPH, the "Engine Coolant Overtemperature" message was displayed on the instrument panel. The accelerator was depressed and failed to respond as intended. The vehicle started losing motive power. The contact was able to coast to the side of the road. The contact inspected the vehicle and noticed that there was no coolant inside the reservoir. The contact added coolant to the vehicle. The vehicle was restarted, and the contact drove to the residence; however, the failure recurred, and the coolant reservoir was empty. The vehicle was taken to the dealer, and it was diagnosed and determined that the radiator had failed. The vehicle was repaired. The dealer diagnosed the vehicle again and confirmed coolant intrusion into the cylinders, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The approximate failure mileage was approximately 38,500.

1.5 liter Engine built in 2019 has Antifreeze Leaking inside cylinder 1 needs Complete Engine. Also a recall on Electrical System propulsion System and Traction Battery Management System ENERGY Control Module Part Number: 23533.

The contact owns a 2019 Ford Fusion. The contact stated that while the vehicle was parked, the vehicle stalled. There were no warning lights illuminated. The contact took the vehicle to an independent mechanic, where it was diagnosed that the flex plate was loose. The vehicle was then towed to a dealer, where it was diagnosed with a cracked flex plate. The vehicle was repaired. The manufacturer was made aware of the failure, and a case was filed. The failure mileage was approximately 56,660.

The contact's daughter owns a 2019 Ford Fusion. The contact stated that the vehicle failed to start on the first attempt. The contact stated that once the vehicle was started, there was a white-colored smoke coming from the exhaust pipe. The contact stated that while driving at various speeds, the vehicle hesitated while depressing the accelerator pedal, with the check engine warning light illuminated. The vehicle was initially taken to an independent mechanic and was diagnosed with cylinder #2 misfire. The spark plugs were replaced; however, the failure persisted. The vehicle was then taken to a dealer where a diagnostic test was performed, and the result was coolant intrusion into cylinder #2. The contact was informed that the engine short block needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that there were no recalls on the VIN. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was approximately 74,000.

My front camera is often unavailable. I took it in multiple times and they couldn’t find an issue. Recently my back up camera has been acting up. It is unavailable most of the time, other times the screen is black, sometimes it’ll work and then cut out. There is a recall on other ford vehicles for this issue. I looked up if it needs a software update and it doesn’t. We’ve checked the camera and wiring harness and they’re both intact and in good condition.

Coolant leak in engine

See attached document for complaint.

The contact owns a 2019 Ford Fusion. The contact stated while driving at an undisclosed speed, the engine was overheating with the temperature warning light illuminated. The vehicle was restarted, and the contact added coolant to the coolant reservoir; however, the failure persisted. The vehicle was taken to the dealer where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and a case was opened. The contact was referred to the NHTSA Hotline for assistance. The approximate failure mileage was 86,300.

The contact owns a 2019 Ford Fusion. The contact stated while operating the vehicle, there was an abnormally severe shaking and vibration coming from the engine compartment. The vehicle was taken to the local dealer who diagnosed that the flex plate was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 120,547.

a coolant leak in my 2019Ford Fusion cause significant corrosion within the engine due to the coolant leaking into the cylinders, and now I have to pay out of pocket to replace the engine, a known problem that ford is aware of with their cars.

During the month of dec 2024 my car didnt start. I called Triple A to jump start my car to get home. During Christmas break of 2024 i purchased a brand new battery and now a month and two weeks later the battery is completely dead again. Sometimes is hard to get the car up to speed and feels like it struggles to maintain it as well. The electrical system also kicks my radio connection off and on while driving. The first incident happened dec. 21,2023 and the second incident happened Jan. 27,2025.

See attached document for complaint

The contact's son-in-law owns a 2019 Ford Fusion. The contact stated while the driver was driving at approximately 55 MPH, the vehicle stalled. The driver was able to coast to the side of the road. The vehicle failed to restart and was towed to the dealer, where it was diagnosed with a catastrophic transmission failure. The dealer determined that the transmission needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 78,000.

The contact owns a 2019 Ford Fusion. While the contact's son was driving at an undisclosed speed, the cruise control failed to function as intended. The contact stated that the vehicle was shaking erratically, and the brakes independently activated. Additionally, the check engine warning light was illuminated. The contact stated that the failure had occurred while her son was driving on a busy highway. The vehicle was pulled over to the shoulder of the roadway. The vehicle was towed to the dealer where it was diagnosed with a failed electric actuator. The contact was informed that the electric actuator, gaskets, and spark plugs needed to be replaced. The vehicle was being repaired. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 82,000.

The contact owns a 2019 Ford Fusion. The contact stated that while depressing the accelerator pedal, there was a loud whining sound coming from the engine compartment. The vehicle was taken to the local dealer who diagnosed the vehicle and determined that the engine flex plate had failed and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 64,000.

A wrench warning light came on, and a warning "SHIFT SYS FAULT Service Required" appeared on the dashboard. This warning appeared when I tried setting the dial to park in the car, and the "P" on the dial was blinking. I could not put the car back in park and had to apply the emergency brake to ensure the car stayed parked. Luckily I was back at home when this happened and was not out in public where this could have caused an accident if I was not able to switch from reverse "R" to "D" for example. After checking online and physically checking the part myself I found the issue to be with the transmission shifter bushing (part # KV6Z7K340A) being missing/degraded. This follows the same issue noted in recall #22V413000 which was for the 2013-2016 fusions, but it should be expanded to the 2018-2020 models too. The vehicle has not been officially inspected due to the fact it cannot be driven anywhere, however, I have ordered the parts from the local Ford dealer for replacement. The failure mileage was 82,670 miles.

The contact owns a 2019 Ford Fusion. The contact stated while driving approximately 60 MPH, the vehicle started losing motive power. The contact stated that the vehicle was making an abnormal humming sound under the floorboards. The contact stated that an unknown warning light and the “WRENCH” symbol was displayed on the instrument panel. The contact was able to exit the highway however, the vehicle was no longer able to accelerate as designed. The contact stated that while depressing the accelerator pedal, the vehicle was only revving. The contact had the vehicle towed to a local dealer where it was diagnosed and determined that the transmission had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was informed of the failure. The failure mileage was approximately 99,000.

2019 Ford Fusion SE 1.5L. Not made aware of CSP on my car. Have dealer notes saying my car wasn’t listen in OASIS for notification. Although when I found the CSP online my car is an “affected vehicle”. I now have low coolant, white exhaust smoke and severe knocking from my engine. I had a first ever reported issue to the dealership in 05/2023 where my car stalled out and dash lights illuminated. They ran codes and the only documented code in the service paperwork was P0222. They found a “chaffed wire”. They did not upgrade my PCM. Although by 05/2023 that was the recommendation on the CSP for the dealership to do after previously failed bandaid fixes by Ford. My car will be going to the dealership on 12/9/24 to address my concerns and request all of my detailed service records. And really figure out why exactly the dealership didn’t complete ANYthing issued in the CSP especially when I was taking my car to the dealership for routine maintenance. I am within the 6 or 7 years and 84k miles or whatever it is now. It continuously changes but honestly I am quite upset that faulty engines aren’t being recalled by Ford but Ford will issue a recall on BACK UP CAMERAS. Like seriously. Engine > camera A faulty back up camera is probably not the same level of fire/safety risk as the faulty engines Ford continues to refuse to recall.

The contact owns a 2019 Ford Fusion. The contact stated that while having a routine oil change, the mechanic observed a leak in the oil pan. The vehicle was taken to three dealers and one independent mechanic where it was diagnosed that there was an oil pan gasket leak and the oil pan gasket needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 60,000.

The contact owns a 2019 Ford Fusion. The contact stated while driving at an undisclosed speed, the vehicle went into limp mode with the check engine warning light illuminated. The contact pulled the vehicle over to the side of the side. The contact inspected the vehicle with a vehicle scanner and received two error codes p0302 -cylinder misfiring and p1299 – cylinder overhead failure. The vehicle was towed to the dealer where it was diagnosed that coolant leaked into the cylinder which caused the long block to fail. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 139, 870.

Coolant intrusion of engine

Flex plate cracked at 84000 miles. It is currently at a Ford dealership being repaired at my expense. The car exhibited a rattling noise at idle near the bell housing. Had the part in question shattered at highway speeds, the results would have been catastrophic. There were no warning indicators other than the rattling noise. From researching this issue, it seems to be a widespread problem with the 1.5l eco boost, but it is not part of the recall.

I have a 2019 Ford Fusion hybrid titanium, and it is exhibiting issues of a recall that Ford has issued for my year making model. But not specifically for my Vin. The recall is for the A.P.I.M. module and is a software glitch that although leave the infotainment system with a black or blank screen or right after using the backup camera, the backup camera will stay on the screen for some time and it states on the recall that it is a safety concern due to being a distraction for the driver on top of that, it will not remember any device I pair to it via Bluetooth, it will not remember navigation presets or any destinations I previously routed to with the navigation system. Every time I turn my car on for some reason it starts the navigation system with the route to my parents address. Also sometimes the screen will be unresponsive and unusable untill next ignition cycle. It kills my 12v battery because the screen will stay on after vehicle is turned off. This happens every ignition cycle

The contact owns a 2019 Ford Fusion. The contact stated that the vehicle was difficult to start after refueling. The contact stated that several attempts were needed to start the vehicle. The contact stated that the failure was a recurring failure. The contact stated that the check engine warning light was illuminated and remained constantly illuminated. The contact had taken the vehicle to an independent mechanic where it was diagnosed and determined that the canister purge valve was stuck and needed to be replaced. The vehicle was repaired. The contact researched online and became aware that the failure was a known failure; however, there was no recall on the VIN. The manufacturer was not informed of the failure. The failure mileage was approximately 66,000.

The lower latch/tether fails to secure the car seat. Any time that the lower latch is tightened for installation, it becomes loose within an hour of installation. The car and car seat were taken to the local fire department to be installed by a certified installer and it still came loose within a hour of installation. The lower latch will not remain sufficiently tightened and the unoccupied seat can move horizontally, laterally and vertically about 3-4 inches. The seat will loosen even when unoccupied by a child.

The contact owns a 2019 Ford Fusion. The contact stated while driving at approximately 65 MPH, the engine started running rough and then the vehicle stalled. The contact stated that the vehicle was blowing white smoke from the exhaust and was idling rough while starting the vehicle in the morning. The contact stated that the "Coolant Overheating" warning light was illuminated. The contact had taken the vehicle to an independent mechanic who diagnosed and determined that there was coolant intrusion into the engine block. The mechanic recommended that the engine be replaced. The vehicle was not repaired. The manufacturer was informed of the failure. The contact researched online and related the failure to TSB: 19-2346 - Coolant Intrusion into the Engine Block (Engine and Engine Cooling). The failure mileage was approximately 83,000.

The contact owns a 2019 Ford Fusion. The contact stated that upon starting the vehicle and shifting the gear selector into the drive position the vehicle shifted back into park on its own. After which a warning message displayed reading "Transmission shifter fault." The transmission warning light was illuminated. The vehicle was towed to the dealer, who diagnosed a failure with the shifter bushing. The vehicle was repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA hotline for assistance. The failure mileage was 131,000.

Transmission failing at 58940 miles on the car. Tour converter clutch is constantly engaging and disengaging. Symptoms started within to last 5000 miles and is quickly getting worse.

Coolant leaking into engine due to the head gasket issue - 2.0L woth eco boost engine - same thing in a 1.5L on fusions but ford or no one will recall it- same issue

1. What component or system failed or malfunctioned, and is it available for inspection upon request? Answer: The Hybrid system/battery caught fire. The vehicle is with the Insurance company Allstate, I believe should be available for inspection upon request. 2. How was your safety or the safety of others put at risk? Answer: The vehicle caught fire after just dropping my kid in to his school, the school has to be evacuated as the vehicle burned near the building. 3. Has the problem been reproduced or confirmed by a dealer or independent service center? Answer: There is an existing recall "Phev battery cell degragation" from Ford. Here is the Campaign/NHTSA#: 23S33/23V440 4. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Answer: The Fire Marshall and the Police was present and we had Police report(case num: [XXX]) and Fire Marshall report(case num: [XXX]) 5. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? Answer: I did notice an unusual behavior, like minutes before the fire the AC fan suddenly turned up blowing a non cold air, I attempted to turn off the vehicle 2 or 3 times until the fan and the vehicle completely turned off. I turned it back on to have AC again and it was good, after like less than 5 minutes I turned off the vehicle to get out of the car with my kid to drop him in his school. Minutes after I returned to the car, there was already smoke, had to call 911 after that. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2019 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle would misfire, with the check engine warning light illuminated. The vehicle was able to restart however, the failure recurred. The vehicle was taken to the dealer where it was diagnosed that coolant intrusion leaked into the cylinders of the engine which caused the engine to fail. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 90,000.

Took my car to get looked at due to car overheating, jerking and smoke coming from muffler within a few weeks turns out air coolant leaking into engine. Had to get new engine paid $5,500.

The contact owns a 2019 Ford Fusion. The contact stated while driving 15-20 MPH in light rainfall, the windshield wipers were activated and the front driver's side windshield wiper suddenly reversed, struck the cowl, and seized. Additionally, the contact stated that there was a significant amount of smoke coming from underneath the driver's side hood, reducing the visibility of the roadway. The contact attempted to deactivate the windshield wipers using the switch; however, the wipers failed to respond as needed. The contact pulled over to the side of the road and turned off the vehicle. The contact opened the hood and allowed the smoke to dissipate. The contact then drove to the residence. The vehicle was taken to the dealer, where it was diagnosed that the windshield wiper motor had failed and needed to be replaced. The vehicle was being repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 37,000.

The contact owns a 2019 Ford Fusion. The contact stated while driving at an undisclosed speed, there was an engine misfire, and the vehicle jerked abnormally with the check engine warning light illuminated. The vehicle was restarted; however, the failure recurred. The vehicle was taken to the dealer where it was diagnosed with coolant intrusion into the engine, causing engine failure. The contact was informed that the engine needed to be replaced. The manufacturer was made aware of the failure. The failure mileage was approximately 50,879.

The contact owns a 2019 Ford Fusion. The contact stated while driving at an undisclosed speed, the vehicle shuddered and loss automotive power. No warning light was illuminated. The vehicle was towed to an independent mechanic where it was diagnosed and determined that the spark plugs needed to be replaced. The vehicle was repaired; however, the failure persisted. The vehicle was towed back to the independent mechanic where it was diagnosed that the coolant reservoir tank needed to be replaced. The vehicle was repaired; however, the failure persisted. The vehicle was taken to a different independent mechanic where it was diagnosed that the engine needed to be replaced. The contact researched and was made aware of an unknown recall; however, the VIN was not included. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 56,000.

Ford had a TSB 22-2322 and previous recalls due to coolant intrusion for vehicles equipped with1.5L engine instead of long block replacement ford is requiring short block replacements vehicle has been in service almost 2 months and has had engine replace twice in 1 year span and now needs a cylinder head replacement due to engine overheating and leaking due to those coolant intrusions and I’m expecting to pay out of pocket which is extremely frustrating