2017 Chrysler Pacifica Complaint Log

The power steering will intermittently go out when traveling down the roadway and when making right and left hand turns. Once the power steering goes out there is an alert triggered and the alerts the driver the power steering assist is malfunctioning and the steering wheel is very difficult to control or turn and jerks the steering wheel. Also, the power steering will re-engage and return to normal function without warning and then go back out again.

The auto start/stop malfunctioned and then the engine sounded like it was going to die. It is available to look at. I thought it was going to stop in the middle of the road. Unknown Unknown The auto start stop light came on and said it was unavailable. They just first appeared today. And the engine light is on.

I keep getting check engine lights and they have repaired serval of the items and I did get a letter in the mail saying the battery would now have a lifetime warranty if it threw a certain code and I had two codes come up and some people told me to replace my 12v battery and it would probably clear up. so reset the codes and put new battery in and ran fine for a week or so (I don't drive much) then when I got in the other day and had it fully charged and it showed on screen only 69% and I thought that was strange then the check engine light came on again showing code P0A0A high voltage system interlock circuit so I am really worried the battery is having a problem and needs replaced. Will it be covered under the lifetime warranty? I see on safety recalls that these vehicles were recalled??

I experienced a check engine light and intermittent starting issues with my vehicle (Chrysler Pacifica Hybrid 2017). [XXX] At times, the vehicle would not start, but after some time it could start again. After researching the issue online, I found that there are active safety recalls for this vehicle related to the hybrid system (including battery and inverter/PIM). I immediately contacted the dealer: [XXX] An appointment was scheduled for April 1, 2026 at 4:00 PM. I dropped off the vehicle at approximately 3:50 PM and handed over the keys. Prior to visiting the dealer, I purchased a diagnostic subscription tool to better understand the issue, as many owners report dealers misdiagnosing these problems. The diagnostic results indicated issues related to the PIM (Power Inverter Module), including required updates and possible internal diode failure. This matches the symptoms I experienced, where the vehicle would intermittently fail to start. I have attached photos showing error messages related to PIM update and hybrid system faults. On the next day, the dealer informed me that they would only perform a diagnostic for $180 instead of processing the issue under recall. I believe this is incorrect, as the symptoms match known recall conditions (loss of power / hybrid system failure), and recall-related diagnostics should not be charged to the customer. The dealer is refusing to proceed under recall and is attempting to charge for diagnosis. This is a safety issue and should be handled under recall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The steering wheel sticks in a slight right and left turns (from about the 11:00 or 1:00 position) when I straighten out the wheel. It does it on highway on and exit ramps, during passing maneuvers and any slight right or left bends in the road. There are no unusual noises associated with this. During these gradual curves the wheel will not self-center to return to straight ahead. Extra force is required to force the steering to respond resulting in the car jerking right or left. This is unexpected and very scary when it first happens because I feel I've temporarily lost control of the steering. My passengers are alarmed as the car is jerked to the side at highway speeds wondering why I'm jerking the car so violently while performing a gradual turn or passing another vehicle. It seems to happen more on long drives (2 to 3 hours) and not so much on short drives. It almost feels temperature related as I don't notice this behavior on short drives around town but mostly at higher speeds on expressways. This has been occurring over the last several years but only noticeable on long road trips.

For several months I have been having problems off and on with my vehicle not shifting into drive, neutral, or reverse. It runs fine but becomes undrivable. Until this last time, I was always able to keep trying, let it sit overnight, etc... and it would eventually shift into gear. Currently it does not, I had to have it towed to a shop to be repaired. This is a problem, the vehicle has left me stranded on several occasions. My daughter was recently home from collage and I could not let her use my car for fear she would get stranded somewhere. It was towed to a local shop, who was able to confirm that the transmission has an internal short. This is a very common occurrence with this vehicle. The transmission can not be repaired and it needs a new one. Each time the transmission would fail a dash light would come on with a P in a circle with an explanation mark next to it and an engine light. This happened several times, in the past I was able to clear the light and drive the car, but this time it would not clear. The transmission is shoot and needs to be replaced. I purchased the car new in February of 2017, and have always properly maintained the vehicle. It has approximately 79,800 miles on it. I have researched this issue and it is very common, this is a known problem with the 2017 Chrysler Pacifica. I have attached a Warranty Bulletin that seems like it should cover my vehicle, but I called the Chrysler Customer Hotline and they are telling me my vehicle is not covered. I have taken care of this vehicle, I drive it very gentle, there is no way this transmission should have gone bad. I am going to get this repaired at the shop, they have ordered me a new transmission. The Chrysler case ID # is [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Check engine light came on at 87K miles, took to dealership and code was P0303. Dealer had to replace 6 spark plugs, warped head, head gasket and oil change. Dealership knew of this problem with faulty heads from the manufacturer and no recall has been started from Chrysler. Car has never overheated or shown any other symptoms. It has been 2 years, 3 months and less than 27K miles and I have another check engine light with the same code. Dealerships says I have another blown head gasket, and it needs to be replaced. Vehicle cannot be driven until it is replaced.

Vehicle “slams” into gear and goes into “limp” mode. RPM’s increase dramatically and speed accelerate ration is very low. Check engine light on and several U codes show. And P0301

My 2017 Chrysler Pacifica experienced repeated engine timing and oil system failures. The vehicle first developed a check engine light and engine timing code (P000D – camshaft position slow response). The vehicle was inspected by a dealership service department. Shortly after, a major engine oil leak was discovered from the oil cooler / oil filter adapter assembly. The vehicle required repair of the oil cooler assembly and associated seals. After that repair, the vehicle continued to experience engine timing issues. The dealership later confirmed failure of the cam phaser components associated with the engine timing system and performed a repair. Within days of the repair, the check engine light and engine timing code returned again. The failure involves the engine valve timing system and oil pressure dependent components based on Autozone code check. Improper camshaft timing can affect engine operation, cause loss of power, rough running, or possible engine stall while driving, which creates a safety risk in traffic. The issue has been inspected and confirmed by a dealership service department. The vehicle is available for inspection upon request.

Vehicle lost power, steering, and breaks on the george washington bridge in NYC causing it to roll into the back of another vehicle.

Intermittent power steering issues with steering wheel becoming “stuck” in one position. Also steering wheel gives resistance while turning at slow speeds, becoming jerky at times.

we've had to replace the engine. Twice and the electric power steering quit, working completely.And now they want five thousand dollars to replace it.When it's a known problem.

Description of Incident: On February 15, 2026, my 2017 Chrysler Pacifica Hybrid experienced three distinct and severe safety system failures involving the electrical system, power seats, and the power sliding door. Power Sliding Door Sensor Failure: While my minor son was entering the vehicle, the power sliding door closed on his leg. The pinch sensor failed to detect the obstruction and did not reverse. This resulted in physical bruising and marks on the limb (photographic evidence maintained). Unintended Passenger Seat Motion: While the vehicle was stationary, the front passenger power seat moved forward to its maximum limit without user input. I was seated in the chair at the time and was pinned against the dashboard before I could intervene. Electrical Shock: My minor daughter received a perceptible electric shock upon touching the exterior door-handle button to open the sliding door. Components Involved: Electrical System Seats (Power) Sliding Door (Power) Injuries: Yes (Soft tissue bruising/marks to minor’s leg). Risk to Safety: Had the driver's seat moved forward without input while the vehicle was in motion, this absolutely could result in loss of control of the vehicle and an accident. Had the sliding side door continued to close on my son's leg, it could have caused severe injury. Had the electrical shock been worse, it could have resulted in burn or injury. The vehicle is available for inspection. It has not yet been inspected by the manufacturer, police, or insurance. The issues have not repeated at this point, although the vehicle was not used the last 12 days. I do not have confidence in its electrical components. There were no warning lamps, messages, or other indications of any problem with the vehicle.

The vehicle is experiencing multiple serious mechanical failures affecting the brake system, powertrain, and steering/wheel components. The brake system produces a constant hissing sound and appears to have lost braking assist. When the brake pedal is depressed the vehicle continues to roll forward and requires excessive force to stop. The vehicle has rolled forward while braking at intersections, creating a significant safety hazard for both the driver and surrounding traffic. These symptoms were first reported on February 4, 2026. Shortly afterward the vehicle was inspected by a Chrysler dealership, which documented a brake vacuum leak in the braking system. Despite that inspection and documentation, the braking condition has continued to worsen and the vehicle no longer feels safe to operate. The braking performance is inconsistent and stopping distance appears to be increasing. In addition to the braking failure, the vehicle experiences powertrain issues including transmission hesitation, delayed shifting, and loss of power during acceleration and when driving uphill. The vehicle also has severe vibration and instability originating from the front driver-side wheel or steering area while driving, which affects vehicle stability and control. These combined mechanical failures involving braking, drivetrain operation, and steering/wheel stability create a serious safety risk during normal operation, particularly while braking in traffic or attempting to maintain control of the vehicle. The vehicle currently feels unsafe to operate due to these worsening conditions and unresolved mechanical defects.

The check engine light is on my Chrysler Pacifica 2017 Limited with error codes P0302 and P0306, indicating misfires in the second and sixth cylinders. The vehicle was purchased brand new in 2017 from a Chrysler dealership in Olathe, Kansas and currently has approximately 97,000 miles. So far, the spark plugs and valve cover gasket have been replaced, but the same error codes persist. The mechanic is now recommending head gasket replacement, with an estimated repair cost of up to $5,000, which is extremely high. After researching this issue online, I found that thousands of Chrysler owners have experienced the same problem, yet no recall or corrective action has been issued by Chrysler. I contacted Chrysler customer support directly, but was informed that no assistance could be provided because the vehicle is out of warranty. We chose to purchase this vehicle based on the trust, reliability, and customer service reputation of Chrysler, but unfortunately, this experience has not reflected those values. An engine failure of this magnitude at this mileage is unacceptable, especially when it appears to be a known and widespread issue. I strongly believe Chrysler should take responsibility and provide assistance for this engine defect.

After purchasing a used 2017 Chrysler Pacifica from Massey Cadillac of Orlando, a warning light appeared during the initial drive indicating a malfunction in the Auto Start/Stop system (capital letter “A” inside a circle with an exclamation point). The system was disabled and indicated service was required. The vehicle was inspected by an authorized Chrysler dealership, which confirmed that the auxiliary ESS (Engine Stop/Start) battery was missing, not failed. Installation of the auxiliary battery and associated mounting hardware was required, indicating the component was not present in the vehicle at the time of inspection. The auxiliary ESS battery is part of a safety-related system. The servicing dealership advised that operating the vehicle without this battery can result in intermittent loss of power steering assist and potential loss of motive power without warning, increasing the risk of a crash. The condition was confirmed by an authorized dealer and is available for inspection upon request. The warning indicator appeared immediately upon operation of the vehicle following purchase. No collision occurred, but vehicle occupants, including children, were placed at risk due to the missing safety component.

2017 Chrysler Pacifica Minivan Right passenger door fell off and out at the back when my wife was opening the door manually in NJ 20 degree temp - - almost injuring my wife. The back end corner of the door fell to the ground when both the top support and middle support came completely out of their tracks. The door is still attached front bottom. The door is very heavy and could have cause severe injury if rear corner landed on a foot or a child. It also shattered the glass corner and track behind the door throwing shards of broken sharp pieces over the floor as shown in pics.

We purchased the vehicle in 2020 with appx 33,000 miles. In fall 2023- winter 2024 it began having electrical glitches when the weather was cold. The car will start, but will not shift into gear. It throws alarms such as service Parking Brake, Shifter, Engine, Traction Control and that you must put it in Park. Although it obviously is in park or it wouldn't have started. The dealership kept it for a month Nov-Dec 2023 and could not get it to recreate the problem, but replaced the battery since it "failed". We went on vacation for Christmas and had issues with it not shifting after it sat all night in the cold. However, the problem is intermittent. But the cold seems to be the consistent factor. Once the weather warms up, it does fine. Although 1 time in sumer 2024 with very high temps 100+ it threw the same alarms and would not shift into gear upon starting the car. We continued to have issues in Fall 2024/Winter 2025. It did great throughout spring and summer, began issues again in Fall 2025 into this Winter 2026. It has left us stranded, unable to get the car to shift sometimes for 10-15 minutes while we "warm up the car" but sometimes it takes 30-60 minutes. We've began putting a space heater nearby it for a couple of hours each morning before we need to drive it, but that doesn't always work either. While extremely frustrating, it hasn't been considered dangerous until a week ago. We came out of church and it was chilly, so I expected it would not shift into gear. It surprised me when it started AND shifted. However, as soon as I got on the main road up to 40mph, the engine completely lost power and threw all the same alarms. The stretch of county road had no shoulders and deep ditches, so barely made it coasting to a neighborhood to pull over. Searching on the Internet, we narrowed it down to the CAN BUS star connector, replaced it, and it drove better than ever! Until it was cold that night! Likely needs soldered, can't reach it behind glovebox.

Steering wheel sticks when making gradual turns in curves when around the 11 o’clock and 1 o’clock positions. Living in a state with snow and ice makes driving scary, not knowing if my steering wheel will stick in a curve. Took it to a repair shop, but they said it would need to be looked at by the dealership.

The contact owns a 2017 Chrysler Pacifica. The contact stated that while driving approximately 40 MPH, the vehicle became difficult to maneuver. The power steering warning light was illuminated. The vehicle was taken to a dealer, where it was diagnosed; however, the vehicle was not repaired. The contact researched and became aware of an unknown recall; however, the VIN was not under recall. The manufacturer was not notified of the failure. The failure mileage was approximately 42,000.

The contact owns a 2017 Chrysler Pacifica. The contact stated that while driving at 60 MPH, the vehicle intermittently started jerking. The vehicle shifted into another gear. There were no warning lights illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 89,090.

When going around a curve (several times this has happened), the steering wheel feels like it is sticking which causes me to have to jerk it to get it out of that position to keep from wrecking, however this is dangerous and could cause an accident. It happens every time I drive it. No warning lights and no one knows what’s causing it. I have done research and this seems to be an ongoing issue with this specific vehicle.

We bought this vehicle from a local dealer in March (9months ago) in the time we’ve had it… it’s been in the shop for about 6 of them. 1- About 3 weeks after the purchase it shut off while I was driving on the highway. We then took it to the dealership in Jasper, Ga bc the error code said the pcm needed to be reset. They couldn’t get it to reset so they embarked on a diagnostic that took 3 months to discover the fuel pump was “too small”. The dealership repair guy assured us this was a solve to the issue, they’re tech put 200 miles on it an had no issues. 2- The day we got it back the check engine light came on and while going around a curve to the right, the wheel locked up on me and almost drove me into a mailbox. We turned around and went right back to the dealership. They had it for another couple weeks and told us we needed a new rack and pinion. We couldn’t afford the $6000 they wanted to fix that. So we then called the guy we bought it from and he had a local repair shop take a look and they replaced some parts on the rack and said it was good to go. 3- got it back and the check engine came on again, they code said pcm needed to be reset. We couldn’t get the dealership to call us back so we went to the local shop o’reileys recommended and they deducted some gauges needed to be replaced. 4- within a couple weeks the van was sputtering and cutting off again, we took it back to the local shop and the only thing they could think to do was change the auxiliary battery. 5- we’ve had it for about 2 weeks… 2 days again I went to start it up and it cut off. I had to wait a few minutes to try again and it started. Then yesterday while driving we stopped a red light and something popped and the dash lit up with errors and a grinding noise started. We went to accelerate to turn and started rolling backwards while in drive. We slammed on the brakes, turned the cautions on and put it in park and still rolled backwards. We had to get a tow back to the local shop.

After a curb impact, the vehicle immediately experienced a no‑start condition. The failure appears to be collision‑related electrical damage in wiring routed through the lowered‑floor mobility‑conversion area installed by BraunAbility. The vehicle was fully operational before the impact and became completely inoperable immediately afterward, with no warning lights or prior symptoms, creating a safety risk for mobility access. United Access (BraunAbility dealer) performed no diagnostic scan, no wiring inspection, and produced no documentation. They stated they could not identify the cause or access the wiring. Houston Dodge Chrysler Jeep Ram produced no diagnostic findings. Their only record, a Multi‑Point Inspection, showed no codes, no scan results, and no wiring notes, and incorrectly marked the visibly damaged left front tire as “OK.” The technician who completed the MPI left shortly afterward, and no further diagnostic work was done. The General Manager, Ben Nash, confirmed in writing that no repairs were performed and the diagnostic fee was waived. United Access reported that the dealership told them there were “two shorts in the wiring harness,” but this was only a verbal statement with no documentation, scan report, or technician notes, and no facility has been able to confirm it. An independent repair facility replaced the battery, but the vehicle still would not start. They reported that the wiring is extensive and non‑standard due to the BraunAbility conversion and reached a wiring‑complexity impasse. BraunAbility stated they conducted a “thorough review,” but provided no diagnostic evidence and relied entirely on undocumented verbal statements. The precise failure point cannot be confirmed because no facility could access or trace the conversion‑zone wiring, but the sequence of events clearly indicates collision‑related electrical damage. The vehicle remains in a no‑start condition.

This car has had so many issues in the 2 years that i have had it. Blown head gaskets, hard shifting, cruise control getting stuck in a high gear and not shifting. When fixing the head gasket it was apparent that it wasnt the first time being fixed. For such a nice vehicle it has way too many problems for the amount i purchased it for. There needs to be some sort of compensation for this. Upon looking into these issues there are thousands among thousands of people with the same head gasket issues and transmission issues as well.

Our Pacifica loses power randomly and doesn't always start when we push the start/stop button. The passenger side window rolls down and power controls all go haywire causing a loss of power. The dash flashes a quick message to service the BCM and the check engine light comes on. It's intermittent and sometimes happens in the middle of the road while driving. It's gotten worse now that it's cold outside, but I don't know if that's related. I checked our VIN against recall 19V-348 but it isn't listed.

I keep getting the same codes every few weeks. P0732

The contact owns a 2017 Chrysler Pacifica. The contact stated that while driving approximately 30 MPH, the steering wheel became difficult to turn to the left or right before the vehicle stalled. The steering assist warning light was illuminated. The vehicle was pulled over and restart and driven to the residence. The vehicle was not taken to a local dealer or independent mechanic to be diagnosed or repaired. Prior to the failures, the vehicle was difficult to start while cold-starting. The contact researched online and related the failure to NHTSA Campaign Number: 19V348000 (Electrical System); however, the VIN was not included in the recall. The manufacturer was not informed of the failure. The failure mileage was approximately 125,000.

The power steering went out without warning. Turned the vehicle on after getting gas and the could not turn when pulling out, then the light for the power steering came on. Checked 2 of the power steering fuse and found that one was a little unseated. Pushed that in and eas able to drive home. Tried to drive the vehicle the next day and the power steering went out while driving. Was able to make it home, but with great difficulty parked at an angle. When trying to move the vehicle to a more appropriate spot the steering wheel was wiggling itself. The power steering warning light is on again. A mechanic has not looked at it yet. We can not afford that but need the vehicle fixed, so plan to attempt to resolve the problem ourselves.

Exhaust (and therefore carbon monoxide) is pumping into my vehicle whenever the cabin air intake is set to pull in out side air (the windshield defogger only works by pulling in outside air). This poses a serious safety concern, as it leaves us with two options: A lose the ability to see out of the windshield by choosing not to run the windshield fan) or B give myself and my children carbon monoxide poisoning. This is a known issue that Chrysler refuses to address because there is no pressure on them to do so, despite the imminent threat to human health and safety.

Brake booster and vacuum failing due to cracked diaphragm

It loses power alot especially uphill. It smells like burnt oil all the time. Smokes out exhaust. Hesitates anytime you put the gas down. And then clunks around sometimes too

The 2nd row seat headrest remains in the forward facing position (parallel to the ground) and not upright. The headrest won’t lock into the upright position anymore which is causing a major safety concern. The head rest will move up and down, but not lock into position. The passenger has to hold the headrest into the upright position or not use the seat at all based on safety concerns of head/neck protection in the event of an accident. No accident or incident has happened. The other headrest on the other side works fine for now, but one is broken. I am requesting this headrest to be replaced free of charge by the manufacturer based on safety concerns and safety protection necessary. In addition, this mode of seat and headrest does not work properly with car seats. We have had to uninstall the headrest in order for a car seat to sit flush with the middle seat so the car seat doesn’t rock back and forth.

2017 Chrysler Pacifica at 70k miles, check engine light came on. After engine warm up, engine starts to rough idle. Diagnosis is misfire on cylinder 2 (code P0302). In addition, vehicle voltage fluctuates in gage cluster between 12-14 volts. No issue until engine is warm and no issue above idle or with load. Injectors were checked and fine, coils and leads were replaced. Fix did not work. Took to Chrysler dealership for addition diagnosis. Dealership diagnosis is cylinder head warpage due to overheating. Single owner of vehicle, regularly maintained and with no “low coolant” engine light.

The contact owned a 2017 Chrysler Pacifica. The contact stated that while the contact's husband was driving at an undisclosed speed, the contact's vehicle was involved in a crash. The contact stated that a nearby vehicle drove in front of the contact's vehicle and then suddenly applied the brakes. In addition, the contact vehicle rear-ended another vehicle. The contact stated that the rear passenger seat belt did not restrain. The contact stated that the waist strap did not restrain. The contact's son, who was seated in the rear passenger seat, was thrown forward. The contact's son did not receive medical attention; however sustained injuries to his neck, back, and right and left shoulders. In addition, the contact's son sustained severe pain in his lap area. The contact, who was seated in the front passenger's seat, later went to the local medical center. The contact sustained severe pain and bruises to both legs from the air bag deployment. The contact stated that the ongoing pain was so severe. The vehicle was taken to a local tow yard. The vehicle was condemned as a total loss. A Police report was filed. In addition, the contact referenced an unknown seat belt recall that was initiated a while ago. The dealer was contacted; however, the contact was informed at that time that the contact's VIN was not associated with the unknown recall. The manufacturer was not made aware of the failure. The failure mileage was approximately 165,000.

About once a week while driving, the steering seems to catch or lock up for a moment. This usually happens when the steering wheel is just slightly off center by 15 or 20 degrees and more often to the left side. You can force to turn through it however it maturely free up and cause you to oversteer and weave on the roadway. It is serious enough that my wife refuses to drive the car. I noticed that there was an alert for steering problems for my type of car but when I entered my VIN number it isn’t included. Why not?? It is exhibiting the exact same symptoms as those that many others have reported. Does there need to be a fatal crash before something done about this critical issue?? VIN # [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

We are experiencing steering wheel locking on right or left gradual turns. The steering wheel locks and it has to be jerked back into a straight position. We've experienced this for over a year now. We understand it may be a chronic problem.

Oil leak from oil filter housing

I have been driving, usually at lower speeds and the entire electrical system shuts down. This has left me and my children in the middle of a busy road without brake lights. It has happened multiple times. The battery will be dead and charge multiple times, but then I end up having the electrical failure. It is terrifying. I had the battery checked and it is not the issue. I have not contacted the dealership, but plan on it tomorrow.

The contact owns a 2017 Chrysler Pacifica. The contact stated that while driving 60 MPH, the message “Service Rack and Pinion Gears” was displayed. The contact stated that it was difficult to turn the steering wheel to the left or right. The contact was able to drive the vehicle to an independent mechanic. The mechanic diagnosed the vehicle and replaced the rack and pinion gears and the steering module. The vehicle was repaired; however, after the repair to the steering, the contact experienced a failure with the transmission. The contact stated that while stopped at traffic signals, after depressing the accelerator pedal, the vehicle failed to respond. The contact stated that several unknown warning lights were illuminated. The contact stated that the engine was running but was vibrating roughly, and then the vehicle jolted forward. The contact stated that the failure was intermittent at first but had become a recurring failure. The contact stated that during another failure, while the engine was running, the vehicle failed to respond as needed. The vehicle was towed to a dealer. The dealer diagnosed the vehicle and determined that the transmission control module needed to be reprogrammed. The vehicle was repaired; however, the failure reoccurred. The vehicle was taken to the same dealer who diagnosed the vehicle and determined that the shifter module needed to be replaced. The vehicle was repaired; however, the failure reoccurred, and the contact had the vehicle towed to the same dealer. The dealer had the vehicle for several days and called the contact to pick up the vehicle, and informed the contact that the vehicle was repaired. The contact stated that the vehicle had failed again, and the vehicle was no longer able to start the vehicle. The manufacturer was not informed of the failure. The failure mileage was 184,136.

Steering sticks occasionally at 1 and 11 position while traveling at highway speed.

Around October/November 2025, the vehicle began having intermittent steering issues that have progressively worsened. The steering wheel becomes stiff or feels stuck, and at times it jerks on its own before correcting. Other times I must pull harder to get it to respond, causing over‑correction and difficulty maintaining my lane. This has happened at various speeds, including 65–70 mph on the interstate, and I nearly collided with another vehicle due to sudden loss of steering control. The vehicle also has ongoing electrical malfunctions. The center screen glitches, causing the heat/air settings to scroll on their own, the radio to constantly scan, and the touchscreen and knobs to stop responding. The navigation system shows incorrect locations, sometimes placing the vehicle in another state or in the ocean. The system has also made random phone calls on its own and has added a second call during an active call without input. During one incident while turning at an intersection, the vehicle lost power and shut off mid‑turn. I coasted to the side of the road and restarted. At the same time, the screen blacked out and flickered, and the ignition button malfunctioned. No warning lights appeared. The battery has died multiple times and has been replaced several times, and software resets have not resolved the issues. These problems were intermittent at first, making it difficult to take the vehicle to a dealer, but they have recently become more frequent and severe. While researching possible causes, I discovered that NHTSA has an open investigation involving similar steering and electrical failures in this model. The combination of steering malfunction, electrical instability, uncommanded inputs, and an engine shutdown presents a significant safety risk.

The internal bearings on the passenger-side sliding door failed. The failure caused the sliding door to come off its tracks, shatter the rear window, and damage surrounding body paint. The vehicle was parked on level ground when the incident occurred. There was no collision or external damage prior to the event. The owner’s manual contains no scheduled maintenance procedure related to the sliding door bearings, hinges, or tracks. This failure appears to be a design or material defect, as multiple other Chrysler Pacifica owners have reported similar sliding door malfunctions. Estimated repair cost is over $3,000. Chrysler customer service was notified. This failure poses a serious safety risk — the door can detach, potentially injuring passengers or bystanders. Please investigate this issue for potential recall or safety campaign.

When making long sweeping turns, like highway off ramps, the steering wheel will stick. The driver has jerk the wheel back towards center to get the wheel to turn again. We have owned the car since new. We have expirenced the problem between 15-20 times. The issue seems to come in waves. We will expirence it a few times in a short time then it wont happen agian for an extended period.

My 2017 Chrysler Pacifica Touring-L has suffered repeated and dangerous electrical failures since purchase. Shortly after buying it from AutoNation Chrysler Dodge Jeep RAM in Valencia, CA, I had to return it twice for electrical repairs that kept it in service several weeks under warranty. About two years later, while still under extended warranty, the engine underwent a complete rebuild for multiple-cylinder misfire codes that were likely caused by intermittent CAN-bus voltage loss rather than a mechanical defect. Over the past nine months, the vehicle has again developed severe electrical faults while driving: sudden loss of power steering assist, all dashboard lights illuminating, windshield wipers activating spontaneously, and the engine failing to shut off using the Start/Stop button. The vehicle has also stalled without warning while driving in traffic or idling at red lights, restarting only after 5–10 minutes and blocking traffic lanes, placing me and surrounding drivers at significant risk. Two major repairs in the last two weeks failed to resolve the defects: (1) repair of the CAN-bus system after the vehicle would not start and acted erratically while driving, and a week later (2) replacement of the brake-booster vacuum pump, which was shorted internally and caused CAN-bus shutdown, complete steering loss, sudden braking, and no engine power. The vehicle is currently at Dependable Chrysler Dodge Jeep Ram, Canoga Park, CA, awaiting further diagnosis despite repeated repair attempts. These symptoms match Chrysler TSBs 08-007-17 and 08-033-21 concerning Body Control Module water intrusion and communication faults. This ongoing electrical defect has caused steering loss, random stalling, ignition failure, and unpredictable vehicle behavior—issues widely reported by Pacifica owners. It poses a serious safety hazard and warrants immediate investigation and recall.

I had the recall for 73B performed in mid October to my 2017 EV/Hybrid Pacifica- 2017 and only 67K miles. No issues before. Since the recall service I’ve brought it in twice with the same problems stating Hybrid Battery needs conditioning/service. I suspect it’s the recall update that has caused all types of issues. I did go to auto zone before I brought the vehicle in just this Monday to get the codes. U0412, P1A29, P0A7F- invalid Data received from Battery energy control Module A - Lost communication with Hybrid Battery Pack Sensor Module- A Deterioration. If you google 73B recall service problems on Chrysler Pacifica - the following appears: Failure to charge and engine light: Some owners have reported that the vehicle no longer charges after the recall service and has a check engine light, with error codes like P0A0A (High Voltage System Interlock Circuit) and P0A7F (Hybrid/EV Battery Pack Deterioration), says Reddit users. Intermittent check engine light: Other owners have noted the check engine light comes on intermittently after the recall service, sometimes disappearing on its own. Battery concerns: Some owners who already had issues with the battery before the recall now report that the recall service did not resolve their problems, and a new, more significant battery issue may have developed. It appears that the issue with the Hybrid battery is not being resolved and the service recall for 73B amplifies issues for the Hybrid Pacifica Models. It may be a ploy from Chrysler for owners to get “rid,” of our vans. I’m contacting the lawyers of the class action lawsuit with this information. It’s so unreasonable for Chrysler to do this and not offer further support. The time, stress, anxiety and loss of a proper running vehicle has really impacted my family.

Have noticed intermittent sticking sensation when driving. No particular direction. Just sometimes happens going around curves. Have to perk steering wheel in opposite direction to free up.

The contact owns a 2017 Chrysler Pacifica. The contact stated that while driving at 35 MPH and turning the steering wheel to the left or the right, the steering wheel became difficult to maneuver. The power steering engaged and jerked the wheel to the left or the right of center. The check engine warning light was illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 154,000.

Power steering sticks while making gradual turns in either direction. Most commonly noted on highway entrance/exit ramps, but also slight curves in the road. Some force is needed to return the steering wheel to the correct position which has led to over correction. This is a repeated issue, not an isolated incident.

When driving on the freeway, at around 65-75 mph, and on a gentle right bend, the steering wheel gets stuck. We can move it, but it jerks the car a little. It initially occurred rarely and was not easily reproduced. My dealer could not reproduce it. It is now becoming more common and a nuisance on road trips. It is also getting more stuck, resulting in more significance movements. I nearly left my lane when getting the steering unstuck this past weekend. We are going to see if our dealer can reproduce it.