2018 Ford Fusion Complaint Log

Unable to shift gears in vehicle and had a Flashing P displayed along with and Shift Sys Fault Parking brake warning. There was a recall already for earlier models of this vehicle for a shifter cable bushing (Recall 22S43). The bushing in my vehicle is disintegrated.

Coolant intrusion in cylinder 1. Confirmed by Suburban Ford of Sterling Heights, MI. Known design flaw. Can potentially cause the engine to seize, misfiring of cylinders, excessive exhaust. Codes for rich fuel mixture and cylinder misfires were found when check engine light appeared. Checked plugs and coils before a camera was put into the cylinder to confirm the coolant intrusion. Dealership and manufacturer refuse to assist with repairs even though there was a recall for certain vehicles with this exact issue.

Coolant Intrusion after the 19B37 customer service program has been completed back in July 23rd 2020 call Ford Motor Company and told them that this service was completed to prevent the coolant intrusion and now it's intruding my car is completely disabled I can't work I bought it with all the money that I had and they said they couldn't do nothing for me they said it's past the 7 years 84,000 miles I tried indicating to them that when disrepair is update was done to the PCM it was supposed to not cause the coolant intrusion but now 6 years later it is causing it so I feel like there should cover it and they basically told me no they don't and have a good day I cannot afford to fix it it's a $6,000 job I do not have that kind of money

Transmission is now not shifting out of park and this is after having issues with the engine allowing coolant to get in and causing damage with the cylinders. Would not pass the pressure test. When calling ford customer service and headquarters telling me there is no way they can help with good will. Find this troublesome when they already know the EcoBoost causing issues to the car and my car is not at 120,000 miles yet. After seeing the 2013-2016 models already have a recall for the exact same thing and you're going to say this is not related is beyond ignorant on the company's behalf.

I am a subsequent owner of this vehicle and it was sold to me with the known issue of coolant intrusion. Not only have I spent over $1000 in repairs. The issue is a known defect with the short block on the engine. While traveling down interstate 275 my car overheated without warning and shut off almost causing a four car collision.

I was driving the vehicle on the freeway when the check engine light appeared and after a few seconds the cars engine suddenly shut off. There was a loss of power steering from the lack of engine power which made it difficult for me to steer and a sudden loss of speed which made several vehicles take evasive maneuvers to avoid having an accident with my car as I merged onto the shoulder of the freeway. After getting the car home I checked the vehicles trouble codes which appeared as P0301 cylinder 1 misfire and P0302 cylinder misfire and P0300 general misfires. I noticed a lack of coolant which I refilled and started the vehicle again to see if and how it would run. The car started but ran very rough at first and white smoke started billowing out of the exhaust. After a couple of minutes I decided to drive just down the street to my local Ford service center. They called me yesterday to tell me that the 2.0L 4 cylinder Ecoboost head gasket has failed and has allowed engine coolant to pour into the cylinder 1. The engine cylinder begins to misfire causing the engine to shake and emit white smoke from the exhaust as the coolant is burned off with the fuel. We are now seeing this safety issue and complaint with many vehicles that have the same or similar engine. They say the only remedy is to replace the long block engine with one that supposedly has a "fix" to the coolant delivery system within the engine block. Knowing what I know now, I would never have considered the purchase of this vehicle. The safety issue alone makes cars with these engines a danger to the owner and the public.

2018 Ford Fusion SE 1.5L EcoBoost, just purchased the car 10 days ago and I already have antifreeze that's mixing with the oil causing the car to overheat and white smoke coming from the back cannot drive the car took it to three mechanics they told me it needs a new turbo and a head gasket which will cost well over $4,000 which I don't have the money that I bought the car with I borrowed from family members so I can go back to work and I don't have money to fix it so at the moment I am unemployed because I have no vehicle to get to work this is a major problem. My father before he passed away had a 2017 Ford Escape with the same engine and he had the same problem he sold it for $1500 lost 14 Grand on it

- There is a crack in the engine block; coolant is leaking into cylinder 3. I am having the car taken by carvana on 3/30 and it will no longer be available for inspection, but I have record of the mechanical issues from taking the vehicle into the dealership on 3/18. - My/others safety was not immediately at risk, but I know that my engine could have blown while driving, causing an accident or even an engine fire. - As stated, issue was confirmed by dealer, and I have records of this - N/A - Check engine light appeared on approximately 3/5; was unable to have car inspected right away and continued driving. Started to get intermittent errors stating that the engine was overheating/coolant was low on 3/12. Stopped driving car more than 2 miles at a time after this. Boyfriend correctly diagnosed issue on 3/15 and I had the issue confirmed by dealer on 3/18.

Leading coolant due to coolant infusion in the block of engine.

Mechanical. Coolant Intrusion on my 2018 Ford Fusion SE 1.5L ecobuster

My car started rumbling and flashing the check engine light. I took it to the mechanic the next day, they tell me to contact Ford because of CSP 21N12 due to my spark plugs having coolant leaking on them and in cylinder, it was misfiring. They tell me the vehicle is unsafe to drive. I call Ford and they say theres nothing they can do. Im screwed out of a car because they closed the CSP's nov 2022 and i just got the car last year pre owned.

While operating my 2018 Ford Fusion, the vehicle began experiencing internal coolant loss resulting in engine misfires, rough running, and white exhaust smoke. The coolant intrusion caused engine failure and loss of reliability. This condition creates a safety risk, as it can lead to loss of power while driving, hesitation, and the possibility of engine shutdown. The defect occurred without warning and is consistent with widespread reports involving Ford EcoBoost engines. This issue is not related to maintenance or normal wear and tear but is a known design defect acknowledged through service bulletins and consumer litigation. Repair requires full engine replacement.

CVT transmission completely failed at 150k miles and is not covered by Ford

The steering wheel is coming loose and is making it hard to drive. The car is becoming seriously dangerous. Others are having issues with this. Please let's fix these cars. I have children!

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle started shuddering violently, hesitated, and failed to accelerate to approximately 35 MPH. The check engine warning light was flashing. The contact related the failure to the Customer Satisfaction Program: 21N12. The vehicle was towed to the local dealer, where it was diagnosed with coolant intrusion into the cylinders. The dealer informed the contact that the engine small block needed to be replaced, but a full engine replacement was recommended. The vehicle was not repaired. The manufacturer was contacted and filed a complaint. The manufacturer advised the contact that a future report would be issued. The failure mileage was approximately 100,000.

My Engine is on my car will not go over 25 miles and if it does it shakes and I place the car in park or shut it off u can hear like water sound coming from the engine were it’s seems as if it was boiling

Shift actuator wouldn’t go into gear I was stranded a few times had to be towed twice. I’ve found a plastic bushing that showed a $4.00 part could be responsible. Deadly for us disabled Vietnam veterans . I can’t walk. Maine has 200 vehicles with the same issues nationwide who knows supposedly the actuator will not be made by ford motors until February 2026. I’m 76 years old this is a hazard I can’t afford to buy another car. Please help us. Or get stranded in the middle of nowhere freezing cold Thank you

Engine replaced due to flaw in design. I had my 60,000-mile service done and after it was completed, I started having serious issues with my vehicle. Kept getting check engine light cylinder 2 misfire. I took my Fusion back to the dealership, and they advised me that my engine had to be replaced. Apparently when they put my vehicle under pressure during the service it caused the coolant to leak into my engine. I have researched this and found many complaints with the same problem. Unfortunately, the owners of the other Fusions (like me) found out their vehicle was no longer under warranty, and they had to foot the entire bill. Luckly for me, I had purchased the Ford Extended Warranty, and my out-pocket pocket is $100. I was told by the dealership that Ford is aware of this issue but has not issued a recall. My service advisor was absolutely shocked when Ford authorized the necessary repairs in a couple hours berceuse it normally takes a few days to get authorization. I have owned this car since it was new and have always kept up with the required maintenance. They gave me a rental vehicle and said it would be about 7 days before the repairs are completed.

Went to back up to park . The shifter would not properly work kept going back to park .I couldn't get it into neutral to push it. No warnings. Had to 1st pay for towing from where it happened to a parking space. Then called roadside service to take it to Bay Lincoln in Panama Beach.i will send the results from dealership. It could of been real serious and caused a bad accident maybe even death. I know ford had a recall on a earlier model fusion for shifter cable. If it's the same issue I want reimbursement.

The contact owns a 2018 Ford Fusion. The contact stated that upon starting the vehicle, there was an abnormal rattling sound coming from the engine with white smoke coming from the exhaust system, with the check engine warning light illuminated. Additionally, the message “Service Vehicle Soon” was displayed. The vehicle was taken to a local dealer, where it was diagnosed, and the contact was informed that the engine was faulty due to coolant intrusion. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 84,112.

Coolant is leaking into the cylinders and causing overheating and no start.

The contact owns a 2018 Ford Fusion. The contact stated that after the engine was replaced, there was an abnormally loud banging sound coming from the engine compartment. The vehicle was taken back to the local dealer, who diagnosed the vehicle with a cracked engine flex plate. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The failure mileage was 59,851.

Coolant intrusive. New motor needed

I would like to respectfully request that my 2018 Ford Fusion, with the 1.5L EcoBoost engine, be considered for inclusion in the customer satisfaction programs related to the engine issues I'm experiencing. Despite my vehicle not being initially listed, the problems I've encountered, including the diagnostic trouble code P0302 and the coolant leak into cylinder #2, suggest that it may be suffering from a similar defect or design flaw that the program aims to address. Given the safety risks associated with the current condition of my vehicle, I believe it would be fair and reasonable to include it in the program and provide the necessary repairs or replacements to ensure the vehicle is safe to operate. I would appreciate your assistance in facilitating this process and exploring options for resolving this issue in a manner consistent with the treatment of similar vehicles.

What component or system failed or malfunctioned, and is it available for inspection upon request? The APIM (Accessory Protocol Interface Module) appears to have failed. The vehicle's infotainment/play screen is completely blank and unresponsive. This module controls key systems including climate control, navigation, hands-free calling, and the backup camera. The component is available for inspection if needed. How was your safety or the safety of others put at risk? This failure compromises several safety-critical functions. I am unable to adjust climate settings, use GPS navigation, make hands-free emergency calls, or see through the backup camera. These features are essential for safe driving, especially in adverse weather or while reversing. Has the problem been reproduced or confirmed by a dealer or independent service center? Not yet confirmed by a dealer, but the issue has been consistent. I have attempted both soft and hard resets, and verified the fuses are good. All symptoms point to an APIM failure. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? No formal inspection has been done by the manufacturer, police, or insurance. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? There were no warning lamps or messages. The issue started intermittently about two months ago. Resets worked temporarily, but the screen is now completely unresponsive.

Shifter cable bushing degraded and fell off. Causing a condition where the car could not be shifted into or out of gear, and car applied park brake as a safety precaution and could not be disabled until the shifter was manually put back into park by mechanic. This bushing has been under recall for other year fusions but has not been extended to this one. Research on forums shows this is a very common problem. Could be a real safety issue if car cannot be shifted and it needs to be driven away in an emergency. This part should not fail in this short of time, it is made of inferior materials and does not last. No warnings given prior, part fails catastrophically.

The contact owns a 2018 Ford Fusion. The contact stated that while driving out of the driveway at 5 MPH, the engine light illuminated. The contact stated that the vehicle was difficult to start. The contact stated that the failure was like Customer Satisfaction Program: 21N12. The vehicle was taken to the local dealer for an oil change, and unknown engine repairs were completed. The vehicle was repaired, but the failure recurred. The vehicle was taken back to the local dealer, and it was determined that the engine needed to be replaced. The vehicle was not repaired. The dealer referred the contact to the manufacturer for assistance. The manufacturer was contacted and the referred the contact to the NHTSA Hotline. The manufacturer declined financial assistance, and stated that the issue would be escalated to the negative feedback department. The failure mileage was approximately 69,000.

The car issued no warning, lights or messages prior to the damage. My [XXX] son was driving and the car started shaking which really scared him as he’s a new driver. I would say the safety of him and other drivers on the road were definitely put in danger. The vehicle has been inspected by a Ford dealership. They stated it had a broken flex plate and short block. Broken Flexplate; Diagnostic $210.00 Parts $1,345.86 (Flexplate, transmission fluid pump, filter, one time use parts) Labor $2,600.00 ($200.00 x 13.0hrs) Sales Tax $125.84 Total $4,281.70 Short Block replacement; Diagnostic $145.00 Parts $2,193.64 (Short block engine/kit, spark plugs, one time use parts) Labor $4,480.00 ($200.00 x 22.4hrs) Alignment $159.95 Sales Tax $205.11 Total $7,183.70 Tow Bill $140.00 INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Engine failure due to coolant leaking into cylinders. This is a known issue. Also Ford has issued a bulletin on this. but no recall yet! I still own 10k on my car and now a blown engine.

Coolant intrusion, coolant and oil is mixing causing my car to run hot. Engine light keeps coming on, repairs to multiple pumps replaced, water pump replaced, spark plugs replaced, radiator replaced, thermostat replaced. Ford dealership tried replacing all the above vehicle is still running hot. Now claiming I need a new engine.

UNKNOWN

The contact owns a 2018 Ford Fusion. The contact stated that while driving at various speeds, there was white smoke coming from the rear exhaust. The check engine warning light was illuminated. The vehicle was taken to a local dealer, where it was diagnosed with coolant intrusion into cylinder #3, low coolant, and an overheated engine. The vehicle was not repaired due to the cost. The contact related the failure to TSB: 19-2208. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 76,000.

Known issue with 2013 Models through 2019, Sunroon leaks under heavy rain even if the Drains are cleaned and cleared. I spoke with Ford and they said it is not their issue since there is no recall. This has been posted under multiple site that there are hundreds of people effected by this.

The contact owns a 2018 Ford Fusion. The contact stated that the check engine warning light was displayed on the instrument panel. The vehicle was taken to an independent mechanic, where a code reader determined that there was a misfire in cylinders #1 and #3. The vehicle was taken to a dealer, where the engine misfires were confirmed, and the engine's long block needed to be replaced. Upon investigation, the contact discovered Technical Service Bulletin: 22-2229; however, the vehicle was not covered under the TSB. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA Hotline to file a complaint. The failure mileage was 88,300.

Engine light came on got it diagnosed said it was misfiring in cylinder 2. spark plugs and coil needed to be changed. Changed all spark plugs and coil and the engine light is still on and saying the same thing. Doesn’t crank right. Coolant going into engine. My vehicle only has 32,000 miles. Seems to be a know problem but ford will not do anything. Saying I need a new motor.

The contact owns a 2018 Ford Fusion. The contact stated that upon starting the vehicle, the vehicle started shuddering. The contact stated that the check engine warning light was illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed that there was coolant leaking into the cylinder. The mechanic informed the contact that the engine needed to be replaced. The contact called the local dealer for parts; however, the vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the VIN was not under recall for the failure. The failure mileage was approximately 91,000.

The contact owns a 2018 Ford Fusion. The contact stated that the vehicle was idling roughly with the check engine warning light illuminated. The vehicle was taken to the dealer, who suggested that the spark plugs be replaced and a tune-up be performed based on the mileage. The dealer performed the spark plug replacement and tune-up, and the check engine warning light was no longer illuminated; however, the vehicle was still idling roughly. The vehicle was returned to the dealer, who diagnosed the vehicle with coolant intrusion into the engine. The contact was informed that the engine had failed and needed to be replaced. The dealer diagnosed the vehicle and determined that the rear brakes and rear brake rotors needed to be replaced due to a brake fluid leak. The vehicle was not repaired. The contact was informed of NHTSA Campaign Number: 23V162000 (Service Brakes, Hydraulic); however, the VIN was not included. The vehicle was not repaired. The manufacturer was informed of the failure and opened a case. The manufacturer informed the contact that the VIN was not under recall or special programs for the repair. The failure mileage was approximately 73,000.

The engine cooling system and engine block failed due to coolant intrusion into the engine cylinders. This issue has been diagnosed by an independent mechanic and is available for inspection upon request. Yes, the problem has been confirmed by an independent service center, which diagnosed coolant intrusion into the engine block, a known issue on this engine. The shop recommended full engine replacement and stated this is a common failure in this vehicle. Not yet by the manufacturer, police, or insurance. The issue has only been inspected by a certified independent mechanic. Yes, a check engine light appeared along with a coolant temperature warning message. The vehicle also began to idle roughly, produce heavy exhaust, and consume coolant. These symptoms began appearing shortly before diagnosis in June 2025. I own a 2018 Ford Fusion with a 2.0L EcoBoost engine. The vehicle recently began experiencing coolant loss, heavy exhaust, and check engine alerts. A certified mechanic confirmed that coolant has intruded into the engine block, causing internal misfires and risk of major engine failure. I was told this is a common and well-documented issue with this engine design, yet there has been no official recall from Ford despite similar problems affecting other models (referenced in Ford TSB 19-2208). The mechanic has recommended a full engine replacement with an estimated cost of $13,000. This is a serious safety concern, as the engine can overheat, stall, or seize while driving.

Coolant intrusion into engine cylinder #2 causing misfire and low coolant levels and overheating and stalling. See Ford TSB 22-2229

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle briefly began to shake violently before returning to normal functionality. The check engine warning light was illuminated. The vehicle was taken to the dealer, who determined that coolant intrusion into various cylinders had resulted in damages to the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 130,000.

My Vehicle was found to have a coolant intrusion. There is a know defect on these vehicles (1.5 / 2L) Ford engine. There was a hairline crack in 2 of the cylinders, which causes coolant to leak thoroughout the engine. My safety was put at risk as this issue causes the vehicles engine to overheat at an unsafe rate. 2 separate dealers found this issue CBA and Autonation Ford. Fidelity Warranty Services inspected the vehicle to see what would be covered. they appeared about 2 weeks prior but would disappear. It finally came back but was extremely repetitive

2018 fusion AWD Titanium, less than 70,000 miles, no warning, no reason. Driving 70mph on interstate when low coolant light comes on, check engine light comes on, car starts losing power and running rough, finally full stall in middle of freeway with catastrophic engine failure due to coolant leak and faulty design. Car was not low on any fluids as they were checked everyday before it was driven. This could have gotten me and my children killed and quite frankly I dont know how it didn't. I bought this car with 44k miles on it. Drove it less than 30k miles and had catastrophic engine failure. This was AFTER I had it in the shop several times for crank shaft position sensor, wouldn't start, and several other problems. The car was taken care of and in immaculate condition. Ford knew these engines would fail prematurely and continued to manufacture them and sell them.

My vehicle has had the check engine light come on intermittently. I took a look under the hood to see if I could spot any issues. The only issue seen was the coolant level was low. After refilling the coolant and a short time driving, perhaps 50-60 miles, the light went out. Then the light came back on a couple days later. Without making any changes the light went out a couple days later. It has done this several times and I thought it may be a faulty sensor or something. I have recently taken it to the dealership for a tune-up, emissions test, multipoint inspection and a transmission flush. I informed the service person that the check engine light will come on and go out and the only thing I have done to the vehicle was add coolant. He suggested the complimentary diagnostic to further identify the issue. During the diagnostic process the auto tech discovered that the coolant has been leaking into the number 2 cylinder. This is the reason for both the fluid loss and the check engine light. From my understanding this is a known issue with my vehicles engine type and has been for some time now. The only fix is to replace the engine. My overall issue is that the safety light (CEL) will say that there is an issue and then it goes away signifying the issue is resolved. The potential hazards of this could possibly lead to an individual unknowingly putting themselves and others at risk with an engine that is prepped for failure. An engine that could overheat, catch fire, throw a rod, or simply lose power in a very dangerous location. For example the freeway, a bridge with heavy traffic, or on train tracks…etc. I believe the risk of failure and potential to lose a life should be considered heavily against the cost of a recall. I don’t believe during the buying process it has ever been disclosed that this specific engine is prone to this problem. I know I would not have made my purchase knowing the engine would need to be replaced within the first 10 years of ownership.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the message “Low Engine Oil Pressure” was displayed. The vehicle was taken to the dealer, where it was diagnosed with coolant intrusion into the cylinders. The contact was informed that the engine block needed to be replaced. The vehicle was not repaired. The contact related the failure to Customer Satisfaction Program: 21N12 (Short Block Replacement After Coolant Intrusion); however, the vehicle was not covered. The manufacturer was made aware of the failure and a case was filed. The failure mileage was approximately 54,000.

At approximately 67,180 miles, a Ford dealership performed a multi-point inspection on my 2018 Ford Fusion SE with the 1.5L EcoBoost engine due to a check engine light on. The Ford dealership diagnosed the vehicle with a coolant intrusion into cylinder 2. The Ford dealership recommended the replacement of the short block and gasket kit, with an estimated repair cost of $7,465. This type of issue diagnosed for my vehicle is a known failure issue for 1.5L Ford EcoBoost engines documented in Customer Satisfaction Program 21N12, which covers coolant intrusion and engine damage in this engine type. Despite the Ford dealership diagnosis of my vehicle matching what is described in Customer Satisfaction Program 21N12, I was informed that my vehicle is not eligible. The Coolant intrusion into cylinder 2 is an issue that poses a safety risk due to engine misfires, stalling, overheating, and possible sudden loss of engine power while driving. In my case, my vehicle has become unreliable and unsafe for regular driving. A Ford dealership inspected the vehicle, confirmed and documented the issue, and the repair quote, diagnostic report and diagnostic payment receipt are available upon request. Ford has declined assistance despite the vehicle’s low mileage and clear alignment with known engine defects. I mailed a formal appeal letter to Ford Motor Company and I am filing a complaint with my state attorney general. This widespread issue affects customer safety, and vehicle safety standards and deserves further investigation, as many other Ford owners of vehicles with 1.5L EcoBoost engines have reported similar failures.

The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, the engine overheated and the check engine warning light illuminated. In addition, the contact noticed white smoke coming from the exhaust, and the engine was running abnormally rough. The vehicle was taken to the dealer, where it was diagnosed with coolant intrusion in cylinder #1, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 115,000.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at various speeds, the vehicle shuddered upon depression of the accelerator pedal. The contact stated that while at a complete stop, there was an abnormal popping sound coming from the vehicle while depressing the accelerator pedal. The failure persisted, and the contact stated that the steering wheel was loose while operating the vehicle. The contact stated that the traction control warning light flashed on the instrument panel during one of the failures. The vehicle was not yet diagnosed or repaired. The manufacturer was notified of the failure and informed the contact that there were no recalls on the VIN related to the failure of the vehicle. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was approximately 41,000.

The contact owns a 2018 Ford Fusion. The contact stated that the low coolant warning light had illuminated prematurely. Upon inspecting the vehicle, the contact was unable to find a coolant leak. Additionally, the contact stated that the vehicle overheated while driving, which required the contact to pull over temporarily and to resume driving after the vehicle had cooled down. The vehicle was taken to a certified mechanic, where it was diagnosed that there was coolant intrusion into the engine, which caused the engine to slowly fail. The vehicle was not repaired. The dealer was notified of the failure. The contact related the failure to an unknown recall. The manufacturer was informed of the failure and confirmed that the VIN was not included in the recall. The manufacturer referred the contact to the NHTSA Hotline to file a safety complaint. The failure mileage was approximately 150,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, the engine overheated with the check engine warning light illuminated. The contact stated that the message that the engine was overheating was illuminated. The vehicle was restarted after the contact added coolant to the reservoir. The contact stated that after adding coolant to the reservoir, the failure recurred. The vehicle was taken to an independent mechanic, where it was diagnosed that coolant had leaked into the cylinders, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired, and the contact was referred to the dealer for further assistance. The dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was 155,000.

I was driving as normal I went to make a turn and out of nowhere my car would not turn and almost got smashed on the side of the car would not have swerved out of the way. There was no warning signs lights symptoms or anything one minute it was normal the next was what could have been a deadly situation. After getting a mechanic to diagnose it after removing the steering wheel, because initially was thought the steering column went out or broke, it was found out to be the middle of the steering wheel where it connects to the column that is suppose to be the shape of an Alan wrench was almost completely worn down to almost a flat circle. I cannot stress enough how scary and deadly this could have been to me and other motorist. This was verified by mechanics this is not normal wear and tear this has to be a defect.