2018 Ford Fusion Complaint Log

The contact owns a 2018 Ford Fusion. The contact stated while driving 40 MPH, the vehicle started shuddering significantly and the engine overheated. The check engine warning light was illuminated. The contact continued driving at 20 MPH. The vehicle was driven to the residence. The vehicle was then taken to the dealer, where it was diagnosed and determined that there was a coolant intrusion in the engine. The dealer determined that the engine needed to be replaced and related the failure to Ford Campaign Number: 21N12 and TSB Number: 22-2134. The vehicle was not repaired. The manufacturer was notified of the failure but denied assistance in covering the cost of the repair. The failure mileage was approximately 110,000.

The contact owns a 2018 Ford Fusion. The contact stated that while at a stoplight, the vehicle hesitated and jerked. The contact depressed the accelerator pedal, but the vehicle hesitated and lost motive power. The service vehicle message was displayed. There was a highlighted rectangle displayed. The vehicle was taken to the local dealer, where it was diagnosed and DTC: P0218/P177S was retrieved, and it was determined that the transmission needed to be replaced. The vehicle was not repaired. The vehicle was taken to another local dealer, Academy Ford Sales (13401 Baltimore Ave, Laurel, MD 20707); where it was diagnosed that the transmission, intermittent clutch, and shaft needed to be replaced. The vehicle was not repaired. The vehicle was taken to an independent mechanic who determined that the transmission needed to be replaced. The vehicle was repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 70,000.

On [XXX], My car began attempting to overheat. This caused me to stop, and park the car until it cooled down, multiple times. (Unsafe) All of my fluids have been filled and checked occasionally prior to this. After multiple roadside trips, I presented my car to AutoNation FORD which is located on Philips Highway in Jacksonville, Florida. An inspection was performed on my vehicle over the weekend which proved my car in fact has a coolant intrusion which is the Latest Recall for the Ford Model. The dealership informed me that my car does not qualify under the recall due to the mileage of the vehicle which is currently 130k. This seems so unfair because I did not do anything wrong that led to this. I am unable to drive my car a mile or 2 without it trying to overheat. This is a risk and I do not feel safe operating this vehicle. It was also very displeasing hearing that operating the unsafe vehicle is my only other alternative besides coming out of pocket with 14k. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The vehicle started jerking violently out of nowhere while being driven only 35 MPH. It immediately became unsafe and unable to be driven without any warning whatsoever. No lights on the dash or anything leading up to this issue. After being diagnosed we were told the transmission needs to be completely replaced. Also after doing some research we have discovered that this is a well known issue with this vehicle that has not been addressed with this year model, but was with previous model years.

The contact owns a 2018 Ford Fusion. The contact stated that after her son had placed the vehicle into reverse(R), the vehicle failed to respond when shifted into drive(D). The contact stated that the WRENCH (Transmission) warning symbol appeared on the instrument panel. The vehicle was towed to the dealer where a diagnostic test was performed. The contact was informed that the shifter cable bushing and the shifter cable bushing cap needed to be replaced. The manufacturer was notified of the failure and referred the contact to the NTHSA Hotline to report the failure. The vehicle remained in the possession of the dealer unrepaired. The failure mileage was approximately 60,000.

The contact owns a 2018 Ford Fusion. The contact stated that while starting the vehicle, the vehicle shuddered with white smoke coming from the exhaust pipe. The check engine warning light was illuminated. The failure had occurred on several occasions. The vehicle was taken to an independent mechanic where it was diagnosed with coolant leak into the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and filed a complaint. The vehicle remained at residence unrepaired. The approximate failure mileage was 140,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, the vehicle experienced rough idling. The check engine warning light was illuminated. The vehicle was taken to the dealer, where the spark plugs were replaced, but the failure persisted. The vehicle was taken back to the dealer, and the contact was informed that the fuel injector in cylinder #3 needed to be replaced. The vehicle was then taken to Terrebonne Ford (339 St Charles St, Houma, LA 70360), where it was determined that there was coolant intrusion into the cylinder block and the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 80,000.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, there was an engine misfire with the check engine warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed and determined that the spark plugs had failed and needed to be replaced. The vehicle was repaired; however, the failure recurred. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the issue and referred the contact to the NHSTA Hotline for assistance. The approximate failure mileage was 122,000.

At 68,000 miles, the transmission began experiencing symptoms of a failed transmission. I took it to the dealer and they confirmed that there was a CONCERN HARSH SHIFT ON 3RD GEAR AND DIAGNOSE DIRECT DRUM CAUSING CUST CONCERN AND SHUDDER CONCERN TORQUE CONVERTER. This diagnosis caused the vehicle to hard shift everytime i would take off and often time cause a kick on the transmission. Because of this, the rear main seal of the engine also gave out prematurely. While driving on the freeway, the engine began leaking oil suddenly from the rear main seal causing the entire bottom of the engine to get soaked with oil. This also caused the oil to fall in to the brake pads and rotors. While driving on the freeway, i lost braking power and could not stop safely. I had to pull to the shoulder and attempt to stop the vehicle. Fortunatelly, there were no cars on the soulder and was able to stop the vehicle. This is where i discovered the vehicle full of oil in the bottom of the vehicle along with the brake pads and rotors. The vehicle was towed to the house about 130 miles. Once discovered, it was taken to Sunrise Ford where they discovered all of the issues. The service tech told me that it is a common problem for those transmissions to fail prematurely and cause other problems. This is a safety issue because after 7 years of the vehicle being on the road with under 100k miles, it is posing a safety hazard not only for the customers but also the public. Please investigate the transmission issue that is leading to other safety issues. This is the 6F35 transmission that is installed on these vehicles. These transmissions are famous for failing prematurely. This was one of those cases. No check engine light comes on to indicate that there is trouble with the transmission. This problem is putting others and oneself at risk because it lead to other failed components. The problem first appeared at 55k miles and around january 2023.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at 45 MPH, the brake pedal was depressed and hesitated to come to a stop. In addition, there was fuel leaking from the rear of the vehicle. The vehicle was inspected by an independent mechanic who confirmed that the brake fluid was leaking from the hose. The vehicle was not repaired. The VIN was not included in NHTSA Campaign Number: 23V162000 (SERVICE BRAKES, HYDRAULIC.)The manufacturer was not notified of the failure. The failure mileage was unknown.

The contact owns a 2018 Ford Fusion. The contact stated while driving at various speeds, the vehicle shuddered and white smoke came out of the exhaust pipe; there was an abnormal sound coming from the engine compartment. The "Engine Coolant Overtemperature" message was displayed on the instrument panel and the check engine warning light was illuminated. The failure occurred on several different occasions. The vehicle was taken to a dealer where it was diagnosed that there was a coolant leak intrusion into the cylinder and that the engine needed to be replaced. The dealer made the contact aware of Technical Service Bulletin Number: 19-2346. The vehicle was not repaired. The manufacturer was notified of the failure and confirmed that there was no recall associated with the failure; the manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 111,700.

The contact owns a 2018 Ford Fusion. The contact stated while his wife was driving 60 MPH, the wrench symbol became displayed. The power train fault warning light was illuminated. The vehicle started to shake with the check engine warning light illuminated. The power steering was inoperable. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 58,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving at 35 MPH, the check engine warning light illuminated. The vehicle was able to restart on the third attempt however the failure recurred. The vehicle was driven to the dealer where it was diagnosed that the engine and the cylinder heads needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and a case was opened. The failure mileage was 13,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving 50 MPH, the check engine warning light illuminated, and the vehicle started sputtering. The vehicle was taken to an independent mechanic, where it was diagnosed with coolant intrusion in the engine. The vehicle was then taken to the dealer, where it was diagnosed with coolant intrusion in the engine. The dealer determined that the short block needed to be replaced. The dealer informed the contact that the failure was related to Ford Campaign Number: 21N12; however, the vehicle was not covered due to the mileage. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that a notice for Ford Campaign Number: 21N12 was previously sent; however, the contact had not received the notice. The failure mileage was approximately 120,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, the check engine warning light illuminated, and the vehicle was driving rough. In addition, the contact noticed that the engine was consuming an excessive amount of coolant. The failure progressed, and the engine started overheating. The vehicle was towed to the dealer where it was diagnosed with a cracked engine and coolant intrusion. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and provided no assistance. The contact referenced Technical Service Bulletin: 22-2134; however, the contact was informed that the repair was not covered under the program. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 27,800.

Driving down the interstate and lost power due to rough running engine. I barely made it to the emergency lane before someone hit me. Coolant intrusion in the cylinders cause the engine malfunction. Ford is fully aware of this problem and refuses to help.

The contact owns a 2018 Ford Fusion. The contact stated that the transmission was previously replaced twice. Additionally, the contact stated while driving 65 MPH, the vehicle stalled. The power train warning light was illuminated. The messages "Shift System Fault”, “See Owner’s Manual" and "Take Vehicle to Service Center Immediately" were displayed. The contact was able to veer to the side of the road. The vehicle was towed to the residence. The contact stated that while shifting to drive(D) or to reverse(R), the gear shifter independently shifted back to park(P). The dealer was notified of the failure and an appointment was scheduled for a diagnostic test. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure milage was approximately 89,000.

Battery Energy Control Module (BECM) malfunction. Causing sluggish response when attempting to accelerate which has nearly caused an accident on multiple occasions. Other vehicles near the date of manufacture of this vehicle are reported having the same symptoms including potential for fire. There is a recall on similar vehicles: Fusion Energi Recall Issued: 2019-2020 - BECM Fire Risk (NHTSA: 23V440, Ford: 23S33) NHTSA Reference: NEF-107DM 23V-440 The date range of vehicles affected most likely needs to be modified to include vehicles manufactured earlier than December 2017. My vehicle, in particular, was manufactured in August 2017 and exhibits the same BECM issue, however, is not currently included in the recall.

The contact owns a 2018 Ford Fusion. The contact stated while attempting to start the vehicle, the vehicle took approximately three minutes to start. The vehicle started after several attempts. The contact stated while driving at approximately 35 MPH, the check engine warning light illuminated. The vehicle was taken to a dealer where it was diagnosed and determined that the vehicle needed a tune up and an oil change. The vehicle was repaired but the power train warning light illuminated. The manufacturer was notified of the failure. The failure mileage was approximately 96,000.

The contact's son owns a 2018 Ford Fusion. The contact's son stated while driving at an undisclosed speed, the vehicle shuddered and white smoke emitted from the exhaust pipe. The check engine warning light was illuminated. The failure occurred on several different occasions and the coolant level was abnormally low. The vehicle was not taken to a dealer. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 90,000.

After reversing out of my driveway I could not get me fusion to go into drive. After getting the car back into my driveway my fusion starting putting the emergency brake on I would take it off and it would automatically put the parking brake back on. After looking at a video of problems with the shifter I popped my hood and found that the shift cable had come off. There is a recall on fusions for this issue but my year is not included.

It was losing calling but no coolant leak, rough idle/driving and blows white smoke out of the exhaust and threw the code p1299 so I took it to a garage and they told me it was the cylinder head gasket but my car has no recalls on it and I looked up my problem and it said 2013-2018 ford fusions with the 1.5l built before June 2019 and mine was built in feb 2018 and I haven’t received any mail about a recall.

The contact owns a 2018 Ford Fusion. The contact stated while driving 45 MPH, the message "Coolant Temperature Overtemperature" was displayed, causing the vehicle to decelerate. The contact stated that another message advising that the engine power was reduced, and to pull to the side of the road was displayed. The contact pulled to the side of the road and checked the coolant level. The contact noticed that the coolant was overheating and leaking. The contact added coolant to the vehicle. The contact stated that the failure recurred intermittently. Additionally, the contact stated that the engine was misfiring on cold starts. A message advising to service the engine soon was displayed. The vehicle was taken to the dealer, where it was diagnosed that there was coolant intrusion in the engine, and the dealer determined that the short block needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the vehicle was not covered under Ford Campaign Number: 21N12 due to the mileage. The failure mileage was approximately 120,000.

Coolant leaked into engine cylinder #4, requiring a new engine.

Shift sys fault message appeared on screen. Car will not go out of park. Shifter bushings are no good. Was told if this had happened while driving my car could not be put in park and could result in a crash.

The car overheated and threw the code p1299, pulled over and there was no visual coolant leak. Put coolant in it and drove it to the garage a few days later, they told me coolant has leaked into the block and that I will need a whole new cylinder block and head gasket. Looked up recalls for my type of car and it showed 2013-2018 ford fusions have recalls about my problem and showed the symptoms and my car has every symptom of that recall but yet there is no active recall for my car.

The contact owns a 2018 Ford Fusion. The contact stated while driving at an undisclosed speed, there was an engine misfire, and the low coolant level warning light illuminated. The vehicle was taken to the dealer where it was diagnosed with coolant intrusion into cylinder #2 and engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure but provided no assistance. The contact was informed that the repair was not covered under Customer Satisfaction Program: 21N12. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 56,000.

2018 fusion ecoboost with no lights or warnings would not start. Took to ford to repair, took them several weeks and several of the same part to fix crankshaft position sensor. Was given a clean bill of health on car. Everything was I'm good condition they said after I paid the 1500.00$ repair bill. Less than 1 week later the car dies while on highway going 65 mph without warning. No lights, nothing. Just sputtered and died. Done all I could to get out of the way so I would not be hit on highway. Catastrophic engine failure resulting in engine locking up had occurred. This car has been taken care of, less than 75k miles on it and the engine is garbage. I lost my job, almost lost my life, lost my home, over half of my possessions all as a direct result of this faulty car that was designed to fail. Ford knows about this engine problem, they continue to sell these cars and refuse to pay for repairs or recall them.

I drive a 2018 Ford fusion ecoboost. It started with a misfire on cylinder 4 and in that same week the engine started to over heat. Had the spark plugs replaced. Upon checking and monitoring coolant levels noticed I was losing coolant. Wasn't having any puddles in the driveway and no visible leaks under the hood. After few trips to work and home the engine would overheat and my work is less than 2 miles from my home. Started to quickly get worse, more codes popping up on my fixt obd2 scanner. From po304, PO300, PO303, B124D, PO313, PO316, PO317.

The contact owns a 2018 Ford Fusion. The contact stated while driving 45 MPH, the engine started to overheat, and there was smoke coming from underneath the hood. The message "Vehicle Temperature Overheating" was displayed. The contact pulled over to the side of the road and allowed the vehicle to cool down. The contact was able to continue driving; however, the failure recurred several times while driving. The contact pulled to the side of the road several times until arriving to the residence. The vehicle was taken to the dealer, where it was diagnosed that the PCM had failed. Additionally, the dealer diagnosed there was coolant intrusion in the engine cylinders. The dealer determined that the engine needed to be replaced. The vehicle was not repaired. The contact related the failure to Ford Campaign Number: 21N12. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 181,000.

Engine has misfire in cylinder one from coolant intrusion. TSB 22-2229. Engine coolant leak can cause many problems for the engine and other components to fail and even break. Dealership confirmed, they’re are other fusion models and same engines with the same problem in the 2.0l. There were no previous lights on the dashboard the car is maintained well.

My fusion has been acting up lately. Everytime I turn on the car In the morning it sounds super rough and it shakes more than usual. I have to fill the coolant every once in a while because the car just eats the coolant up. I took it to a ford dealership to make sure there are no leaks but there weren’t. Car seems to have coolant intrusion by the amount of times I need to re fill coolant. I have attached picture of coolant always below minimum line.

The contact owns a 2018 Ford Fusion. The contact stated that while driving 45-50 MPH, the check engine warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed that the head gasket was blown. The dealer determined that the engine block needed to be replaced. The vehicle was then taken to an independent mechanic, where the engine was replaced. The vehicle was repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 97,000.

My Vin # is: [XXX] and matches TSB 22-2322 // Customer Satisfaction Program 21N12 by all written criteria. My vehicle is exhibiting the exact symptoms as coolant leaking into cylinder bore (#3 in my situation). When I called my local Ford dealership and Ford Corporate office, they told me that my vehicle doesn't fall under that coverage, but couldn't tell me why. My make/model/year/manufacturer date/location/engine, etc. all match what is written in the TSB/CSP. If Ford states that my vehicle doesn't qualify for this program, I need an exact/specific explanation as to why my vehicle doesn't qualify for this TSB/CSP. Nobody can tell me and I keep getting the run around. This is unethical as everything written matches my vehicle and situation but I am being denied coverage. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I took my vehicle into a Ford dealership due to having a engine code of P0302 for engine misfire 8/3/24.Received a call from the dealership stating that I have coolant intrusion in cylinder 2 and has caused catastrophic engine failure.It has never been stated that there had been 2 previous recalls for this issue at any time while owning this vehicle.I called the Ford dealer that I recently had my oil changed at and asked if there was any notes on any issues or concerns when my oil was changed and was told no but there was a recall on the vehicle for this exact issue but it had expired.The dealership stated a new motor is needed costing $5,600 for a short block or $8,600 for a long block.I called Ford Customer Care and was told that with this being an ongoing issue to report it. I am at a loss after reading how many people have had this issue and Ford knowingly has had 2 recalls on it but people are still having to pay for a new engine because of the mileage on their vehicles at engine failure due to the boring between the cylinders causing the head gasket to fail. My car has a little over 135k miles and the previous recall stopped at 85k miles.I don't have an extended warranty and that would be the only way at this point that Ford would cover the expense.When buying a vehicle from a trusted company and then not being notified of an actual recall by Ford or even from the dealerships when being serviced if you aren't having that specific issue I don't think that is ethical or making sure their customers are safe.It puts not only my family but others at risk that have the same engine which can cause engine fires,failure while driving and money out of pocket that shouldn't have to be paid because of a known issue that currently has a pending class action lawsuit over.Ford needs to stand by their customers and reinstate this recall to include higher mileage cutoffs to make things right for all customers with the same manufacturer defect even if it takes longer to comeup

The contact owns a 2018 Ford Fusion. The contact stated while operating the vehicle, the message "Turn Engine Off" was displayed, and the engine temperature gauge indicated that the engine had overheated. The vehicle was taken to the local mechanic who diagnosed that the engine had failed due to coolant intrusion into the cylinders. The contact was advised that the engine short block needed to be replaced. The vehicle was not repaired. The manufacturer was contacted regarding the failure. The failure mileage was approximately 87,000.

The contact owns a 2018 Ford Fusion. The contact stated that the vehicle had experienced rough starts and there was a slushing liquid sound coming from inside the dashboard. Additionally, while operating the vehicle the check engine warning light remained illuminated and the vehicle stalled. The vehicle was taken to the local dealer who diagnosed that the engine block was cracked and causing coolant to leak into the engine. The contact was advised that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was 120,000.

The contact owns a 2018 Ford Fusion. The contact stated while driving approximately 15 MPH, the vehicle stalled occasionally and returned to normal operation once the contact had turned off and restarted the vehicle. In addition, there was smoke coming from the tailpipes. The check engine warning light was illuminated. The vehicle was drivable and was driven to an independent mechanic where it was diagnosed with a coolant leak, and the mechanic suggested that the vehicle be taken to a Ford dealer. The vehicle was towed to a Ford dealer where it was confirmed that there was a coolant intrusion into the cylinder head gasket. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for further assistance. The failure mileage was approximately 135,000.

While driving car started misfiring like crazy out the blue and losing power leaving me stranded by the road in the heat. Come to find out it has coolant intrusion. I have 2018 ford fusion. Luckily it didn't catch on fire but ford is aware of this problem and continues to do nothing.

The contact owns a 2018 Ford Fusion. While the contact's daughter was driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated that the check engine warning light and several other unknown warning lights were illuminated. The vehicle was taken to several independent mechanics; however, the vehicle was not diagnosed. The vehicle was not repaired. The vehicle was towed to the dealer where it was diagnosed with a coolant leak in the engine and engine failure. The contact was informed that the engine and the cylinders needed to be replaced. The vehicle was repaired. The contact was informed of an Extended Warranty Program; however, the contact was informed that the mileage had been exceeded by 9,000 miles. The contact was informed that the repair was not covered under the extended warranty. The manufacturer was made aware of the failure and a case was filed. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 93,451.

The contact owns a 2018 Ford Fusion. The contact stated that after starting the vehicle, the gear shifter could not immediately be shifted out of park(P). The cause of the failure was not yet determined. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The failure mileage was unknown.

Originally, the car had Cylinder 2 misfire followed by the engine overheating. No crash, thankfully. have had this car for approximately 2 years, and put less than 30,000 miles on it. I took the car to Kings Ford Services where they discovered the engine block had been miscast resulting in engine coolant to enter cylinders 2 and 4, thus killing the engine. Spoke with Eric Hutton, Service Advisor Kings Ford Inc, (513)-683-0220 ext. 219, who said he has seen this happen multiple times with Ford Fusions and that the 1.5L has been recalled, but not the 2.0L which my car has. Per Kings Ford Repair Receipt: "Inspected the engine base part number to confirm it I'd 206 then with the engine at normal operating temperature, pressurized the cooling system to 20 PSI FOR 5 hours and the pressure dropped more than 4 PSK. Removed the spark plugs, used a borescope and found coolant has entered the cylinders. Removed the engine and replaced the long block assembly using all of the approved Ford gasket removers, parts cleaners, shampoo and metal surface prep wipes to clean all related mating surfaces per the workshop service manual. Also replaced all other related seals, gaskets, and non reusable hardware and reinstalled all components Removed for repairs in the reverse order of removal. Evachated, pulled system into vacuum, and recharged thr air conditioning system to service the engine assembly." I called Beechmont Ford who filed a claim with my warranty, but the warranty refused to aid and gave many excuses that were not true to the problem such as "it was a gasket issue not an engine" despite Mr. Hutton telling them multiple times it was the engine. I found out later their excuses were just that as Ford Inc. said the warranty expired within a year of having the car. They also had heard of this happening before, as well. Ford Inc. who was willing to pay a portion of the bill, $5,000, despite it being a manufacturing issue. Car was fixed and returned to me on 08/01/2024.

The contact owns a 2018 Ford Fusion. The contact stated that while the vehicle was parked in the driveway, upon attempting to start the vehicle, the vehicle failed to start as intended. The contact stated that when the vehicle was started and idling, there was white smoke coming from the engine compartment. The contact inspected the vehicle; however, no visible fluid leaks were noticed. The vehicle then stalled, and the check engine warning light illuminated. The vehicle was not repaired or diagnosed by an independent mechanic or local dealer. The contact related the failure to an unknown recall; however, the vehicle was not included. The manufacturer was not made aware of the failure. The failure mileage was approximately 30,000. The VIN was not available.

Technical Service Bulletin (TSB) 1.5L EcoBoost for Ford Fusion vehicles built on or before June 10, 2019 may indicate low coolant levels, white exhaust smoke, or rough running conditions Myself and a few of my relatives and friends who have the same vehicle have experienced this and yet no recall was issued when I looked it up by vin . I have called the hotline number several times and have got ahold of no one . I have been on the phone up to an hour each time . I would like someone to contact me pertaining to this I have documentation from dealer in regards of issue. I have sent a letter to ford company pertaining to this and also have foster legal assistance to how I can proceed with getting issue fixed .

My vehicle has an engine defect from the manufacturer Ford. I was told it is a coolant intrusion from the original design of the head of the vehicle engine. I have had it inspected by Bell ford in AZ however, they will not take responsibility of the defect and saying I am liable for repair. I am confused if it’s a defect in a design from a manufacturer how I am responsible for such said repair the check engine light came on, and I took it in for a diagnosis, no prior issues to the vehicle whatsoever ability wise I’ve contacted customer service and they said there is nothing they can do to contact you guys

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, the vehicle briefly hesitated and jerked, prompting the contact to pull over to the shoulder of the roadway. After pulling over, the contact observed that the vehicle was idling rough and turned off the vehicle. Upon attempting to restart the vehicle, the vehicle initially failed to start and required a jump start. The check engine warning light was illuminated. The vehicle was taken to the dealer, who observed coolant intrusion into cylinder #3, resulting in engine damage. The contact was informed that the long block needed to be replaced. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 21N12. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 102,000.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, there was an alarm for the coolant temperature being elevated. The contact pulled over and turned off the air conditioner and the vehicle. The engine cooled off while driving. The vehicle was taken to the local dealer, who informed the contact that coolant was leaking into the engine and the engine needed to be replaced. The vehicle was not repaired. The manufacturer was contacted, but there were no recalls for the failure. The contact was referred to the NHTSA Hotline. The failure mileage was approximately 120,000.

The contact owns a 2018 Ford Fusion. The contact stated whenever cold starting the vehicle, the vehicle idled rough. The contact stated that the check engine warning light was illuminated. The contact had taken the vehicle to a local dealer, where it was diagnosed and determined that coolant had leaked into the engine block and the engine needed to be replaced. The vehicle was not repaired. The contact was advised by the dealer that the vehicle was no longer under warranty coverage under recall: 21N12 - Coolant Intrusion into the Cylinder (Engine and Engine Cooling). The manufacturer was informed of the failure. The failure mileage was 101,080.

The contact owns a 2018 Ford Fusion. The contact stated that while driving at an undisclosed speed, there was an abnormal knocking sound coming from the engine compartment. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the flex plate. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 22N12. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 116,000.

The contact owns a 2018 Ford Fusion. The contact stated that the check engine warning light illuminated while starting the vehicle, with cloud of white exhaust smoke coming from the tailpipe intermittently. The vehicle was taken to an independent mechanic where it was diagnosed that there was coolant leaking into the engine, causing engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure, and it was confirmed that the VIN was not under recall for the failure. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was 73,000.